8/120
KA-BSY+
English
Locking force adjustment
If factory-set locking pressure of ca. 150 N is not
sufficient to close the window, it can be infinitely
increased up to ca. 250 N.
Put in covering stopper after adjustment.
approx. 150 N
approx. 250 N
Ø 6 mm
Locking force adjustment
KA-BSY+
9/20
English
Visual inspection:
Only one main drive is allowed. The main always
has the highest addressing of all the drives; this
can be found on the type plate of the drive. Subs
are numbered downwards from the main, so that in
a group of two drives, for example, the main is no.
2 (M2) with a sub no. 1 (S1) drive. Please note that
this only applies in the ex-factory configuration. As
soon as the drives are re-addressed with SCS, the
ex-factory addressing no longer applies.
Wiring:
Is the group wired correctly?
Therefore look connection diagrams.
Null balance:
It should be null balanced.
Software SCS or the special magnet
MAG 502 is required.
Call D+H Service:
Drives must be configured.
Software SCS is required.
Trouble shooting
99.823.89 3.0/09/23
99.823.89 3.0/09/23
Shift of drive cable
The drive will be full configured by factory.
The drives must be reconfigured in case of
alterations (e.g. removing of drives
from existing set or integrating
a new drive) with SCS.
Mount the drives mechanical stress-free.
With that, a better load distribution
is ensured on all the drives.
Sub 1
Mounting information
DIP-Switch
Only for ex-works programming
Debe ser encendido OFF
B
173,5 mm
A
40 mm
51 mm
Stroke
350
500
600
700
800
1000
1100
1200
1300
247,5
322,5
372,5
422,5
472,5
576,5
628,5
678,5
728,5
A
B
421
496
546
596
646
750
802
852
902
Dimensions
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
Disposal
Maintenance and cleaning
Maintenance work is only allowed when the device is in
a de-energized condition! Inspection and maintenance
has to be carried out according to D+H maintenance
notes. Only original D+H spare parts may be used.
Repair is to be carried out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.
1
2
ON KS
If after mounting the measure x is
as bigger as 23 mm, null balance
with software SCS is neccesary.
Closure Ranges will shift in
relation to new zero point.
A t v e r t i c a l a c t i v e p u l l i n g
application (e.g. for a skylight) the
forces must be rearranged by
software SCS
≥ 23 mm ?
X
For option “IP 42”: the chain
outlet must not point upwards.
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following
:
regulations
2014/30/EU, 2011/65/EU
S.I. 2016/1091, S.I. 2012/3032
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder
Maik Schmees
CEO
CTO
25.09.2023
