background image

3

Manual del Usuario

 / event series / 

User’s Manual

Precauciones de Seguridad
Safety Precautions

Cajas acústicas activas / Self-powered loudspeaker enclosures

line array

Para 

EVENT-26A

, la altura máxima de seguridad desde el suelo a 

la base de la caja montada sobre trípode modelo 

TRD-2

 (necesita 

además 

AXS-EV26

), con pies a 55 cm del eje del trípode, es:

For 

EVENT-26A

, the maximum safety height from floor to bottom 

of enclosure when mounting on a 

TRD-2

 tripod (it needs also 

AXS-EV26

), with legs spread 55cm from the central pole, is:

55 cm

 

1x 

EVENT-26A 

------------->142 cm

 

2x 

EVENT-26A 

------------->132 cm

 

1x 

EVENT-26A 

------------->142 cm

 

2x 

EVENT-26A 

------------->132 cm

The exclamation point inside an equilateral triangle is intended to 
alert  the  users  to  the  presence  of  important  operating  and 
maintenance  (servicing)  instructions  in  the  literature 
accompanying  the  product.  Heed  all  warnings.  Follow  all 
instructions. Keep these instructions.
WARNING: This is a class A product. In a domestic environment 
this product may cause radio interferences in which case the 
user may be required to take adequate measures.
Use  this  product  only  in  E1,  E2,  E3  or  E4  environments 
according to EN55103-2.

Para  desconectar  el  dispositivo  debe  usar  el  enchufe. 
Desconecte  este  aparato  durante  tormentas  eléctricas, 
terremotos  o  cuando  no  se  vaya  a  emplear  durante  largos 
periodos.

To disconnect the device, you should use the mains plug. Unplug 
this  apparatus  during  lightning  storms,  earthquakes  or  when 
unused for long periods of time.

Equipo  diseñado  para  funcionar  entre 15ºC  y 45ºC  con una 
humedad relativa máxima del 95%, con un rango de ±10% de la 
tensión nominal de alimentación indicada en la etiqueta trasera. 
Si debe sustituir el fusible preste atención al tipo y rango.

Working temperature ranges from 15ºC to 45ºC with a relative 
humidity of 95%, with ±10% of the rated main voltage value 
indicated on the rear label. If the fuse needs to be replaced, 
please pay attention to correct type and ratings.

No instale el aparato cerca de ninguna fuente de calor como 
radiadores, estufas u otros aparatos que produzcan calor. Debe 
instalarse siempre sin bloquear la libre circulación de aire por las 
aletas del radiador.

Do not install near any heat sources such as radiators, heat 
registers,  stoves  or  other  apparatus  that  produce  heat.  The 
circulation of air through the heatsink must not be blocked.

No exponga este equipo a la lluvia o humedad. No use este 
aparato cerca del agua (piscinas y fuentes, por ejemplo). No 
exponga el equipo a salpicaduras ni coloque sobre él objetos 
que contengan líquidos, tales como vasos y botellas.
Equipo IP-43.

Do not expose this device to rain or moisture. Do not use this 
apparatus  near  water  (for  example,  swimming  pools  and 
fountains). Do not place any objects containing liquids, such as 
bottles or glasses, on the top of the unit. Do not splash liquids 
on the unit. IP-43 equipment.

No  emplace  altavoces  en  proximidad  a  equipos  sensibles  a 
campos  magnéticos,  tales  como  monitores  de  televisión  o 
material magnético de almacenamiento de datos.

Do not place loudspeakers in proximity to devices sensitive to 
magnetic  fields  such  as  television  monitors  or  data  storage 
magnetic material.

Este  símbolo  indica  que  el  presente  producto  no  puede  ser 
tratado  como  residuo  doméstico  normal,  sino  que  debe 
entregarse en el correspondiente punto de recogida de equipos 
eléctricos y electrónicos.

This symbol on the product indicates that this product should 
not be treated as household waste. Instead it shall be handed 
over  to  the  appicable  collection  point  for  the  recycling  of 
electrical and electronic equipment.

El  cableado  exterior  conectado  al  equipo  requiere  de  su 
instalación por una persona instruida o el uso de cables flexibles 
ya preparados.

The outer wiring connected to the device requires installation by 
an  instructed  person  or  the  use  of  a  flexible  cable  already 
prepared.

Si  el  aparato  es  conectado  permanentemente,  la  instalación 
eléctrica del edificio debe incorporar un interruptor multipolar con 
separación de contacto de al menos 3mm en cada polo.

If the apparatus is connected permanently, the electrical system 
of  the  building  must  incorporate  a  multipolar  switch  with  a 
separation of contact of at least 3mm in each pole.

No desconecte la tierra en el conector de alimentación pues es 
peligroso  e  ilegal.  Equipo  de  Clase  I.  El  producto  debe  ser 
conectado  a  un  enchufe  con  toma  de  tierra.  Sólo  use  este 
equipo con el cable de red de alimentación adecuado para su 
país.
El  signo  del  rayo  con  la  punta  de  flecha,  alerta  contra  la 
presencia  de  voltajes  peligrosos  no  aislados.  Para  reducir  el 
riesgo de choque eléctrico, no retire la cubierta.

Do not remove mains connector ground, it is dangerous and 
illegal.  Class  I device.  The product  must  be connected  to a 
mains socket outlet with protective earth connection. Only use 
this equipment with an appropriate mains cord for your country.

The lightning and arrowhead symbol warns about the presence 
of uninsulated dangerous voltage. To reduce the risk of electric 
shock, do not remove the cover.

El  signo  de  exclamación  dentro  de  un  triángulo  indica  la 
existencia  de  importantes  instrucciones  de  operación  y 
mantenimiento en la documentación que acompaña al producto.
Conserve y lea todas estas instrucciones. Siga las advertencias.
ATENCIÓN: Es un producto clase A, por lo que en entornos 
domésticos puede causar radio-interferencias, en cuyo caso el 
usuario tendrá que tomar las medidas oportunas.
De acuerdo con EN55103-2, usar el equipo sólo en entornos E1, 
E2, E3 ó E4.

El colgado del equipo sólo debe realizarse utilizando los herrajes 
de  colgado  recomendados  y  por  personal  cualificado.  No 
cuelgue la caja de las asas.

The appliance should be flown only from the rigging points and 
by  qualified  personnel.  Do  not  suspend  the  box  from  the 
handles.

No existen partes ajustables por el usuario en el interior de este 
equipo.  Cualquier  operación  de  mantenimiento  o  reparación 
debe  ser  realizada  por  personal  cualificado.  Es  necesario  el 
servicio técnico cuando el equipo se haya dañado de alguna 
forma, como que haya caído líquido o algún objeto en el interior 
del aparato, haya sido expuesto a lluvia o humedad, no funcione 
correctamente, haya recibido un golpe o su cable de red esté 
dañado.

No user serviceable parts inside. Refer all servicing to qualified 
service personnel. Servicing is required when the apparatus has 
been damaged in any way, such as power-supply cord or plug is 
damaged, liquid has been spilled or objects have fallen into the 
apparatus, the apparatus has been exposed to rain or moisture, 
does not operate normally or has been dropped.

Limpie con un paño seco. No use limpiadores con disolventes.

Clean  only  with  a  dry  cloth.  Do  not  use  any  solvent  based 
cleaners.

Содержание EVENT SERIES


































Отзывы: