Cypress SPX-1200 Скачать руководство пользователя страница 2

©2006 Cypress Computer Systems,Inc. • www.cypressworld.com  

Page 2

Part numbers for different versions:

SPX-1200: RS-485 Twisted pair, wired version.

Table of Contents

Quick Reference guides

Page 3,4

General specifications, Dip switch settings

Page 5

Electrical specifications,  Introduction  

Page 6

Status indicators and Dip switch details                                   

Page 7

Identification of major components                                             

Page 8

Detailed terminal connections                                                    

Page 9,10

Power connection                                                                    

Page 11,12,13

Communication connections

Page 14

Reader data connections

Page 15,16,17

Door strike relay

Page 18

Alternate I/O Function - Dip Switch #5

Page 19,20

Auxiliary inputs and outputs

Page 21,22,23,24

Supervised contacts and programming resistors

Page 25,26

This device complies with part 15 of the FCC Rules.  

Operation is subject to the following two conditions:  
(1)  This device may not cause harmful interference, and  
(2) this device must accept any interference received, 
including interference that may cause undesired operation.

FCC Part 15 COMPLIANCE

Содержание SPX-1200

























Отзывы: