background image

 

Copyrights 

CY4502 EZ-

PD™ CCG2 Development Kit Guide, Doc. No. 001-96601 Rev. *G 

Copyrights 

© Cypress Semiconductor Corporation, 2015-2017. The information contained herein is subject to change without notice. 
Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in 
a  Cypress  product.  Nor  does  it  convey  or  imply  any  license  under  patent  or  other  rights.  Cypress  products  are  not 
warranted  nor  intended  to  be  used  for  medical,  life  support,  life  saving,  critical  control  or  safety  applications,  unless 
pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as 
critical  components  in  life-support  systems  where  a  malfunction  or  failure  may  reasonably  be  expected  to  result  in 
significant  injury  to  the  user.  The  inclusion  of  Cypress  products  in  life-support  systems  application  implies  that  the 
manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.  

Trademarks 

PSoC is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced 
herein are property of the respective corporations.  

Source Code 

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected 
by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international 
treaty  provisions.  Cypress  hereby  grants  to  licensee  a  personal,  non-exclusive,  non-transferable  license  to  copy,  use, 
modify,  create  derivative  works  of,  and  compile  the  Cypress  Source  Code  and  derivative  works  for  the  sole  purpose  of 
creating  custom  software  and  or  firmware  in  support  of  licensee  product  to  be  used  only  in  conjunction  with  a  Cypress 
integrated  circuit  as  specified  in  the  applicable  agreement.  Any  reproduction,  modification,  translation,  compilation,  or 
representation  of  this  Source  Code  except  as  specified  above  is  prohibited  without  the  express  written  permission  of 
Cypress.  

Disclaimer 

CYPRESS  MAKES  NO  WARRANTY  OF  ANY  KIND,  EXPRESS  OR  IMPLIED,  WITH  REGARD  TO  THIS  MATERIAL, 
INCLUDING,  BUT  NOT  LIMITED  TO,  THE  IMPLIED  WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A 
PARTICULAR  PURPOSE.  Cypress  reserves  the  right  to  make  changes  without  further  notice  to  the  materials  described 
herein.  Cypress  does  not  assume  any  liability  arising  out  of  the  application  or  use  of  any  product  or  circuit  described 
herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction 
or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-
support  systems  application  implies  that  the  manufacturer  assumes  all  risk  of  such  use  and  in  doing  so  indemnifies 
Cypress against all charges.  

Use may be limited by and subject to the applicable Cypress software license agreement.  

 

 

 

 

 

 

 

 

 

 

Содержание EZ-PD CCG2 Development Kit



































Отзывы: