CybioTronics 60CN57-2 Скачать руководство пользователя страница 58

Страница: 58 / 117

Please refer to the following tips before calling for technical assistance:

Problem(s) Possible

Cause(s)

Solution(s)

No dial tone is heard when

pressing

1. The base unit is not properly

connected to the outside land

line.

2. Too far from the base unit.

3. Batteries are low (low battery

icon is displayed).

▪

Check the cables.

▪

Move closer to the base unit.

▪

Charge the batteries.

When putting the handset

on the base unit, no beep

is heard.

1. The handset is not placed

properly on the base unit.

2. Charging contacts are dirty.

▪

Take the handset off the base unit and

put it back again.

▪

Clean charging contacts with a clean

and dry cloth.

Battery icon remains

empty although the

handset has charged for

24 hours.

1. Handset batteries are

defective.

2. Handset is not placed

properly on the base unit.

3. The power adapter is not

properly connected.

▪

Purchase new Ni-MH rechargeable

batteries (AAA 1.2V 600mAh).

▪

Check whether the power adapter is

properly connected to the main point.

No display on the screen.

1. Batteries are uncharged.

2. The phone is not properly

connected.

▪

Charge the batteries.

▪

Make sure your phone is properly

plugged in.

Bad audio quality

(crackles, echo, etc.)

1. Interference from nearby

electrical appliance.

2. Base unit is installed in a

room with thick walls.

3. The handset is too far from

the base unit.

▪

Move the nearby electrical appliance to

a different location.

▪

Install the base unit in a different room.

▪

Move closer to the base unit.

Cannot hear the other

party clearly / speaker too

quiet.

1. The volume is set to

minimum.

▪

Press

▲

▼

to adjust the phone

volume.

The phone does not ring

when a call comes in.

1. The ringer is off.

▪

Turn on the ringer.

Cannot call a phone

number.

1. The handset has lost link

with the base unit.

▪

Page the handset from the base unit to

ensure connectivity exists.

TROUBLESHOOTING

Содержание 60CN57-2






















































































































Результаты поиска

Содержание 60CN57-2

Отзывы:

Бренды по названию

Популярные бренды

CybioTronics 60CN57-2, Руководство пользователя по установке и эксплуатации

Результаты поиска

Содержание 60CN57-2

Отзывы:

Бренды по названию

Популярные бренды