Custom Audio Electronics TG02H Скачать руководство пользователя страница 56

Страница: 56 / 100

0x1D 0x4C

<GS L>

Set left margin

Valid for

TG02H

[Format]

ASCII

GS L nL nH

Hex

1D 4C nL nH

Decimal

29 76 nL nH

[Range]

0 ≤ nL, nH ≤ 255

[Description]

Sets the left margin.

The left margin is set to [(nL + nH × 256) × (horizontal motion unit)] inches.

Printable area

Left margin

Printing area width

[Notes]

• This command is enabled only if set at the beginning of the line.

• If the setting exceeds the printable area, the maximum value of the printable area is used.

• If the left printing area width is greater than the printable area, the printing area width is

set at maximum value.

• The horizontal and vertical motion unit are specified by 0x1D 0x50. Changing the horizontal or

vertical motion unit does not affect the current left margin.

• The 0x1D 0x50 command can change the horizontal (and vertical) motion unit.

• However, the value cannot be less than the minimum horizontal movement amount and it must be

in even units of the minimum horizontal movement amount.

[Default]

If font A:

nL = nH = 0

If font B:

nL = 14 nH = 0

[Reference]

0x1D 0x50, 0x1D 0x57

[Example]

56 │

ESC/POS™ emulation

Содержание TG02H





































































































Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды

Custom Audio Electronics TG02H, Руководство по управлению

Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды