Custom Audio Electronics TG02H Скачать руководство пользователя страница 85

Страница: 85 / 100

MACRO FUNCTIONS

0x1D 0x3A

<GS :>

Set start/end of macro definition

Valid for

TG02H

[Format]

ASCII

GS :

Hex

1D 3A

Decimal

29 58

[Range]

[Description]

Starts or ends macro definition.

[Notes]

• Macro definition starts when this command is received during normal operation.

• When 0x1D 0x5E is received during macro definition, the printer ends macro definition and clears
all definitions.

• Macros are not defined when power is turned on to the machine.

• Macro content is not cancelled by the 0x1B 0x40 command. Therefore, 0x1B 0x40 may be included
in the content of macro definitions.

• If the printer receives 0x1D 0x3A a second time after previously receiving 0x1D 0x3A, the printer
remains in macro undefined status.

• The contents of the macro can be defined up to 2048 bytes. If the macro definition exceeds 2048

bytes, excess data is not stored.

[Default]

[Reference]

0x1D 0x5E

[Example]

ESC/POS™ emulation

│ 85

Содержание TG02H





































































































Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды

Custom Audio Electronics TG02H, Руководство по управлению

Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды