Custom Audio Electronics TG02H Скачать руководство пользователя страница 57

Страница: 57 / 100

0x1D 0x57

<GS W>

Set printing area width

Valid for

TG02H

[Format]

ASCII

GS W nL nH

Hex

1D 57 nL nH

Decimal

[Range]

0 ≤ nL, nH ≤ 255

0 ≤ nL + nH × 256) ≤ 384

[Description]

Sets the printing area width to the area specified by nL and nH.

• The left margin is set to [(nL + nH × 256) × (horizontal motion unit)] inches.

Printable area

Left margin

Printing area width

[Notes]

• This command is only enabled if set at the beginning of the line.

• If the right margin is greater than the printable area, the printing area width is set at maximum value.

• If the printing area width = 0, it is set at the maximum value.

• The horizontal and vertical motion units are specified by 0x1D 0x50. Changing the horizontal or

vertical motion unit does not affect the current left margin.

• The 0x1D 0x50 command can change the horizontal (and vertical) motion unit.

• However, the value cannot be less than the minimum horizontal movement amount and it must be

in even units of the minimum horizontal movement amount.

[Default]

Se font A:

nL = 192

nH = 1

Se font B:

nL = 164

nH = 1

[Reference]

0x1D 0x4C, 0x1D 0x50

[Example]

ESC/POS™ emulation

│ 57

Содержание TG02H





































































































Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды

Custom Audio Electronics TG02H, Руководство по управлению

Результаты поиска

Содержание TG02H

Отзывы:

Похожие инструкции для TG02H

Бренды по названию

Популярные бренды