Curtiss-Wright SCRAMNet+ SC150e Скачать руководство пользователя страница 13

Страница: 13 / 140

2-1

S SC150e HARDWARE REFERENCE

2. SCRAMNET OVERVIEW

2.1 Overview

The S SC150e Network is a real-time communications network, based on a

replicated, shared-memory concept. Each host processor on the network has access to its

own local copy of shared memory that is updated over a high-speed, serial-ring network.

The network is optimized for high-speed data transfer among multiple, real-time

computers all solving portions of the same real-time problem.

2.2 Shared Memory

In its simplest form, the S SC150e Network system is designed to appear as

general-purpose memory. The use of this memory depends only on the conventions and

limitations imposed by the specific host computer system and operating system. On most

processors, this means that the application program can use this memory in basically the

same way as any other data-storage area of memory. However, the memory cannot be

used as instruction space.
The major difference between S SC150e memory and system memory is any

data written into S SC150e memory is automatically sent to the same

S SC150e memory location in all nodes on the network. This is why it is also

referred to as replicated shared memory. A good analogy is the COMMON AREA used

by the FORTRAN programming language. Where the COMMON AREA makes variables

available to subroutines of a program, S SC150e makes variables available to

processors of a network.
When a host computer writes to the shared memory, the proper handshaking logic is

supplied by the S SC150e node host adapter. The shared memory behaves

somewhat like resident or local memory.
A software driver is usually not required except for interrupt handling.

2.2.1 Dual-Port Memory Controller

The Dual-Port Memory Controller (see Figure 2-1) allows the host to read from or write

to shared memory with a simultaneous network write to shared memory. Unless an

interrupt has been authorized for that memory address, the host is not aware the network

is writing to shared memory. This is why caching must be disabled for SCRAMNet

memory. If an interrupt has been authorized, the interrupt will then be sent to the host

processor.

Содержание SCRAMNet+ SC150e





























































































































Результаты поиска

Содержание SCRAMNet+ SC150e

Отзывы:

Похожие инструкции для SCRAMNet+ SC150e

Бренды по названию

Популярные бренды

Curtiss-Wright SCRAMNet+ SC150e, Справочник по аппаратуре

Результаты поиска

Содержание SCRAMNet+ SC150e

Отзывы:

Похожие инструкции для SCRAMNet+ SC150e

Бренды по названию

Популярные бренды