Cub Cadet THE TANK S6031 Скачать руководство пользователя

Страница: 36 / 48

Service

Battery Removal

WARNING!

Battery posts, terminals and related

accessories contain lead and lead compounds. Wash

hands after handling.

The battery is located on the right/rear of the tractor beneath the

seat box frame. To remove the battery:

Remove the hold down strap.

Remove the hex screw and flange lock nut securing the

black negative battery lead to the negative battery post

(marked nEG). Move the cable away from the negative

battery post.
Remove the hex screw and flange lock nut securing the red

positive battery lead to the positive battery post (marked

POS).

Carefully lift the battery out of the tractor.

Install the battery by repeating the above steps in the

reverse order.

WARNING!

Always connect the positive lead to the

battery before connecting the negative lead. This

will prevent sparking or possible injury from an

electrical short caused by contacting the tractor

body with tools being used to connect the cables.

Charging the Battery

Test and, if necessary, recharge the battery after the tractor has

been stored for a period of time.

A voltmeter or load tester should read 12.6 volts (DC) or

•

higher across the battery terminals. See Fig. 7-1.

Voltmeter

Reading

State of

Charge

Charging

Time

12.7

100%

Full Charge

12.4

75%

90 Min.

12.2

50%

180 Min.

12.0

25%

280 Min.

Charge the battery with a 12-volt battery charger at a

•

MAXIMUM rate of 10 amps.

Jump Starting

WARNING!

Failure to use this starting procedure

can cause sparking, and the gases in the battery to

explode.

Attach the end of the red jumper cable to the positive

terminal (+) of the charged battery.

Attach the other end of the red jumper cable to the

positive terminal (+) of the low charge battery.

Attach the end of the black jumper cable to the negative

terminal of the charged battery.
Attach the other end of the black jumper cable to the

frame of the unit with the low charge battery.

Servicing Electrical System

Fuse

There is one fuse located in the wiring between the ignition start

switch and other electrical components. This is a standard plug-

in type automotive fuse rated at 20 amp. Always use the same

capacity fuse for replacement. If the electrical system does not

function, check for a blown fuse.
If you have a recurring problem with blown fuses, have the

tractor’s electrical system checked by your Cub Cadet Service

Dealer.

Safety Switch Operation Checks

The following operational checks should be made daily:

PTO Switch

Sit in the operator’s seat. With the speed control pedals

in the neutral position and the parking brake engaged,

turn the PTO switch “On” and try to start the engine. The

engine should not start. If it does, the PTO switch must be

replaced. See an authorized service dealer.
If the engine does not start, turn the PTO switch “OFF” and

start the engine. now turn the PTO switch “On” and the

blades should rotate.

If the blades do not turn, the PTO switch must be replaced,

the seat switch must be replaced or the electric PTO clutch

must be repaired. See an authorized service dealer.

Parking Brake Switch

Sit in the operator’s seat. With the speed control pedals

•

in the neutral position and the PTO switch “OFF”, release

the parking brake and try to start the engine. The engine

should not start.
If it does, the parking brake switch must be repositioned or

•

perhaps replaced. See an authorized service dealer. If the

engine does not start, engage the parking brake and start

the engine.

Figure 7-1

Содержание THE TANK S6031

















































Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды

Cub Cadet THE TANK S6031, Руководство оператора

Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды