Cub Cadet THE TANK S6031 Скачать руководство пользователя

Страница: 14 / 48

ectiOn

2— a

sseMbly

& s

-u

Connecting the Battery Cables

CALIFORNIA PROPOSITION 65 WARNING

Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals known

to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

CAUTION:

When attaching battery cables, always

connect the POSITIVE (Red) wire to its terminal first,

followed by the nEGATIVE (Black) wire.

For shipping reasons, both battery cables on your equipment

may have been left disconnected from the terminals at the

factory. To connect the battery cables, proceed as follows:

Using the lever on the back of the seat frame, lift up on the

lever and tilt the seat forward.

NOTE:

The positive battery terminal is marked Pos. (+). The

negative battery terminal is marked neg. (–).

NOTE:

If the positive battery cable is already attached, skip

ahead to step 2.

Remove the plastic cover, if present, from the positive

battery terminal and attach the red cable to the positive

battery terminal (+) with the bolt and hex nut. See Fig. 3-12.

Remove the plastic cover, if present, from the negative

battery terminal and attach the black cable to the negative

battery terminal (–) with the bolt and hex nut. See Fig. 3-12.
Position the red rubber boot over the positive battery

terminal to help protect it from corrosion.

NOTE:

If the battery is put into service after the date shown

on top/side of battery, charge the battery as instructed in the

Maintenance section your Operator’s Manual prior to operating

the tractor.

Figure 3-12

Discharge Chute

Remove the strap or any other device securing the mower deck

dischage chute during shipping. The discharge chute is a spring-

loaded device that must be down for proper and safe operation.

Tires

The tires are over-inflated during shipping to set the bead lock,

so they must be adjusted.

Inflation Pressure

Traction Tires — 20 psi max, 10-12 psi recommended

•

Front Wheel — 25 psi max, 20-25 psi recommended

•

Содержание THE TANK S6031

















































Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды

Cub Cadet THE TANK S6031, Руководство оператора

Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды