Cub Cadet THE TANK S6031 Скачать руководство пользователя

Страница: 11 / 48

ectiOn

2 — a

sseMbly

& s

-u

Install the upper ROPS section onto the lower ROPS “posts”.

Install the (1⁄2

-13 x 3.25) HHCS bolts, nuts and washers. See

Fig. 3-3.

Tighten Upper ROPS section bolts after both RH & LH

hardware is installed.

Tighten the frame mounting hardware to 80-90 lb.-ft.

torque. See Fig. 3-2.

NOTE:

Make sure tubular upright posts are absolutely tight

within welded bracket.

Insert rubber plugs into each side of the upper ROPS. See

Fig. 3-4.

Move the upper ROPS section to the upright position, and

insert the locking pins with their retainer hairpin clips. See

Fig. 3-5.

Position Steering Wheel

The steering wheel of the tractor has been left off for shipping

purposes. Using the hardware found in the manual bag, the

steering wheel must be secured to operate the tractor. To install

the steering wheel for operation, proceed as follows:

Slide steering wheel over the steering shaft. See Fig. 3-6.

Slide washer over steering shaft and secure using hex nut.

Snap steering wheel cover onto steering wheel.

Hex Bolts

Washers

Nuts

Lower ROPS Posts

Figure 3-3

Rubber Plug

Figure 3-4

Locking Pin

Hairpin

Clips

Figure 3-5

Steering

Shaft

Steering

Wheel

Washer

Hex Nut

Steering

Wheel

Cover

Figure 3-6

Содержание THE TANK S6031

















































Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды

Cub Cadet THE TANK S6031, Руководство оператора

Результаты поиска

Содержание THE TANK S6031

Отзывы:

Похожие инструкции для THE TANK S6031

Бренды по названию

Популярные бренды