CTS MCT-RACK-12-MGM Скачать руководство пользователя

Страница: 70 / 103

Media Type:

Shows the type of FX (fiber).

Speed:

Data rate of the slide-in SFP Transceiver.

Distance:

Transmission

distance of the slide-in SFP Transceiver.

Vendor Name:

Vendor name of the slide-in SFP Transceiver.

Vendor PN:

Vendor PN of the slide-in SFP Transceiver.

Vendor SN:

Vendor SN of the slide-in SFP Transceiver.

Temperature (C):

The

Slide-in SFP module operation temperature.

Voltage (V):

The Slide-in SFP module operation voltage.

TX Bias (mA):

The Slide-in SFP module operation current.

TX Power (dbm):

The Slide-in SFP module optical Transmission power.

RX Power (dbm):

The Slide-in SFP module optical Receiver power.

Select

“Rates and Events”

option from the Counters Display pull-down menu to view the

detailed traffic statistics (counters

’ information).

Содержание MCT-RACK-12-MGM








































































































Результаты поиска

Содержание MCT-RACK-12-MGM

Отзывы:

Похожие инструкции для MCT-RACK-12-MGM

Бренды по названию

Популярные бренды

CTS MCT-RACK-12-MGM, Руководство пользователя

Результаты поиска

Содержание MCT-RACK-12-MGM

Отзывы:

Похожие инструкции для MCT-RACK-12-MGM

Бренды по названию

Популярные бренды