CTS MCT-RACK-12-MGM Скачать руководство пользователя

Страница: 27 / 103

MCT-RACK(config)# show
snmp-server trap-destination
[1-10]

[1-10]

Show the specified trap destination
information.

MCT-RACK(config)# show snmp-server trap-
destination

Show SNMP trap destination information in
Global Configuration mode.

MCT-RACK(config-trap-ACCOUNT)# show

View this trap destinatio

n account’s

information.

Exit command

MCT-RACK(config- trap-ACCOUNT)# exit

Return to Global Configuration Mode.

Trap-destination example

MCT-RACK(config)# snmp-server trap-
destination 1

Create a trap destination account.

MCT-RACK(config-trap-1)# active

Activate the trap destination account.

MCT-RACK(config-trap-1)# community
mycomm

Refer this trap destination account to the
community “mycomm”.

MCT-RACK(config-trap-1)# description
redepttrapdest

Add a description for this trap destination
account.

MCT-RACK(config-trap-1)# destination
172.168.1.254

Set trap destination IP address to
192.168.1.254.

Содержание MCT-RACK-12-MGM








































































































Результаты поиска

Содержание MCT-RACK-12-MGM

Отзывы:

Похожие инструкции для MCT-RACK-12-MGM

Бренды по названию

Популярные бренды

CTS MCT-RACK-12-MGM, Руководство пользователя

Результаты поиска

Содержание MCT-RACK-12-MGM

Отзывы:

Похожие инструкции для MCT-RACK-12-MGM

Бренды по названию

Популярные бренды