background image

CANifier 

User’s

 Guide                                                                www.ctr-electronics.com                                                                10/8/2017 

 

Cross The Road Electronics                                                                    Page 16                                                                              10/8/2017 
 

2.5. Enclose/Insulate CANifier assembly 

The recommended approach to insulate CANifier is to shroud entire wire assembly in 1” heat shrink tubing.

 

 
Insert assembly into one side of a precut heat 
shrink tubing. 
 
 
 

 
Heat shrink should cover all 
exposed electrical areas of 
CANifier and LED strip. 
 
 
After applying heat to heat shrink tubing, neatly wrap and separate the harnesses into their logical sub groups.  
Illustrated below are two pigtails for CAN bus, power leads (to PDP/power source), and wire harness for 
PWMs/sensors/etc.  
 
 
 
 
 
 
 
 
 
 

 
Alternatively, the CANifier can be mounted to a fixed location using a 3D 
printed enclosure. 
 
Fixed mounting is accomplished via the two mounting holes in the CANifier. 

These holes are 0.125” in diameter nominally, and act as clearance for a 4

-40 

or M3 screw. A case for the CANifier in STEP and STL formats is available on ctr-
eletronics.com to facilitate fixed mounting while covering the exposed pads. 
 
Use any length 4-40 or M3 screw to attach the CANifier to your mounting 
surface. Ensure that there is no contact between any exposed pads and the 
mounting surface. Plastic spacers can be used to isolate the CANifier from the 
surface. The CANifier can also be mounted with double-side tape, but ensure 
that the tape is nonconductive and that wires are soldered onto the CANifier 
before mounting. 
 

 
 

 

Содержание CANifier






















Отзывы: