background image

DOC00101-01

1-15

CTPhone 1900 System Overview

Calls Initiated from a CTPhone Handset

1

The handset locks onto a system base station and initiates a service
request.

2

The base station transmits calling information to the CTPhone Control-
ler. The call then proceeds like any other call in the office telephone
system.

Call Termination

Call termination involves freeing a voice channel and transition of the
CTPhone handset to a standby state. When the CTPhone Controller
determines that a call has terminated, it sends a release message to the
base station. The base station and handset then terminate the RF link.

In some cases, the base station must initiate call termination by sending a
message to the CTPhone Controller. Loss of handset power, interference
with the RF signal, or a user stepping out of base station coverage are
examples of events that cause the base station to terminate a call.

Regulatory Information (United States Only)

The CTPhone 1900 system complies with Federal Communications Com-
mission (FCC) Regulations Part 15 and Part 68 Subpart C. The FCC Part
68 registration number is 5RYISR-23723-WC-T. The Ringer Equivalence
Number is specified as 0.6B. 

The CTPhone 1900 system is designed to operate under FCC Part 15
rules for Unlicensed Personal Communications Service (U-PCS) equip-
ment in the 1920–1930 MHz band. Part 15 ID numbers for the eight-chan-
nel base station, four-channel “Mini” base station, and handset are MTU-
1900-BS-A1, MTU-1900-BS-B1, and MTU-1900-HS-A1, respectively.

Because microwave services are currently also offered in the 1920–1930
MHz band, the FCC has designated UTAM, Inc. to coordinate the transi-
tion of microwave services to other frequency bands and manage the
installation of new U-PCS equipment in the band. CTP Systems’ CTPhone
UTAM certification ID is MTUCCLUM00006.

The CTPhone 1900 system complies with Underwriters Laboratories spec-
ification UL1459 for safety. The compliance ID is C86-0345.

Detailed information on these requirements is in Appendix A.

Содержание CTPhone 1900





































































































































Отзывы: