CTP Systems CTPhone 1900 Скачать руководство пользователя | Manualshive

Страница: 51 / 132

background image

DOC00101-01

3-3

CTPhone 1900 System Hardware & Software Installation

Recommended Installation Order

Following is the recommended order for installing your CTPhone 1900
system.

Table 3-A. Installation Order

Task

Instructions

1

Install system cabling.

2

Complete base station installation.

3

Complete physical installation and grounding of the
CTPhone Controller. Do not connect the CTPhone
Controller to power at this point.

4

Connect a personal computer to the CTPhone Con-
troller.

5

Install CTPhone Manager software on the personal
computer.

6

Copy CTPhone software onto the personal com-
puter. You must copy the software to the SOFT-
WARE subdirectory underneath the CTPhone
Manager directory.

7

Start the CTPhone Manager and open the Status
Window.

8

Connect the power cable to the CTPhone Controller.
Then connect the cable to power. (You’ll see warning
messages in the status window; this is normal.)

9

Using the CTPhone Manager, perform a software
upgrade to upload the CTPhone software from the
personal computer to CTPhone Controller.

10 Perform UTAM activation (if required).

11 Configure System Settings.

12 Repeat the software upgrade process to complete

loading software from the personal computer to the
base stations.

13 Check CTPhone Controller LEDs to make sure they

do not indicate any failures. Note that dim or flashing
LEDs may indicate a problem.

If LED S2 on the CTPhone Controller remains lit after
powering the CTPhone Controller trying reloading
software using the instructions on page 3-25.

14 Check base station LEDs to make sure they do not

indicate a failure. Note that dim or flashing LEDs may
indicate a problem.

15 If the LEDs indicate a problem, use troubleshooting

procedures to determine the problem.

«
...
49
50
51
52
53
...
»

Содержание CTPhone 1900





































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTPhone 1900

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 8

KX-TG7622, KX-TG7623, KX-TG762

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 6

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 3

Бренд: Harman Страницы: 10

Бренд: Harman Страницы: 2

Бренд: Jensen Страницы: 12

Бренд: Talkswitch Страницы: 334

Бренд: Yamaha Страницы: 108

Бренд: Viking Страницы: 1

Бренд: Uniden Страницы: 47

Box Design BT Box S2

Бренд: Pro-Ject Audio Systems Страницы: 6

Бренд: VTech Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды