CTC Union SDTU-01/ET10 Скачать руководство пользователя страница 8

Страница: 8 / 50

6. Management

SDTU-01/ET10

supports simple, flexible and easy-to-operate

methods for management purpose. The

SDTU-01/ET10

can be

managed via the following paths, refer to Appendix B for
detailed information.

Console port – use the RS232 cable for connecting

SDTU-

01/ET10

to an console terminal or an PC running terminal

emulation program, such as Hyper Terminal, see Appendix A
for proper console setup.

Local Ethernet Port – connect the Ethernet port to your local

area network or to a PC directly, “

Telnet

”

SDTU-01/ET10

from

any workstation in the LAN. The default local Ethernet IP
address is “192.168.2.1”.

SDSL port from remote site – while SDSL connection is in

service, you may remotely “

Telnet

”

SDTU-01/ET10

from a

workstation networking to the CO equipment, the default
Remote Ethernet IP address is “192.168.1.1”.

Note

: As operating SDSL modem requires technical know-how and

experience. It is recommended to manage

SDTU-01/ET10

qualified technical staffs only. Therefore a password authentication
is applied when you enter the command line interface, consult your
service provider for obtaining the appropriate password.

Содержание SDTU-01/ET10



















































Результаты поиска

Содержание SDTU-01/ET10

Отзывы:

Похожие инструкции для SDTU-01/ET10

Бренды по названию

Популярные бренды

CTC Union SDTU-01/ET10, Руководство пользователя

Результаты поиска

Содержание SDTU-01/ET10

Отзывы:

Похожие инструкции для SDTU-01/ET10

Бренды по названию

Популярные бренды