CTC Union SDTU-01/ET10 Скачать руководство пользователя

Страница: 45 / 50

Explanation:

dbit    - normal
scramble - enable
cell   - enable
SDSL Module     -> enable

Status:
Bitpump F/W Version: 4.5
Bitpump: present
CO/RT Select: cpe
Auto Rate: disable
Rate: 2320
Sign/Magnitude Bit Sequence: reverse
Data Bit Polarity: normal
DSL Status: normal operation
Noise Margin: -16.0

Information for SDSL configuration setting:

Version (SDSL driver version number)…………..Ver1.08

SDSL module (SDSL interface)………….enable
(enable: normal operation, disable: malfunction)

Information for SDSL line status:

Bitpump F/W version (SDSL firmware version
number)…………………………………………………..4.5

Bitpump (status of chipset)…..………….present
(present: normal operation, unpresent: malfunction)

CO/RT select (terminal)………………………………..cpe

Auto rate (auto)……….…………………………….disable

Rate (line rate)…………………………………..2320Kbps

Sign/magnitude bit sequence (smbit)……………reverse

Data bit polarity (dbit)………………………………normal

DSL status……………………………….normal operation
(normal operation: connected / during startup: without
connection yet)

Noise margin (noise margin after connection)……..-16.0

( “?” before connection)

Содержание SDTU-01/ET10



















































Результаты поиска

Содержание SDTU-01/ET10

Отзывы:

Похожие инструкции для SDTU-01/ET10

Бренды по названию

Популярные бренды

CTC Union SDTU-01/ET10, Руководство пользователя

Результаты поиска

Содержание SDTU-01/ET10

Отзывы:

Похожие инструкции для SDTU-01/ET10

Бренды по названию

Популярные бренды