CTC Union GW-732FW Скачать руководство пользователя страница 33

Страница: 33 / 86

Dual Band Wireless VoIP Gateway

User’s Manual

2-2-9 Hot Line

General Settings

→

Hot Line

Enable:

Tick the check box to enable a line. If some lines are not used, disable them (Pause Function) to

avoid unnecessary waiting when an incoming call is diverting to the line.

Hot Line:

Check to direct the call automatically to a pre-configured destination without any action when the

FXS is off-hook. (i.e. as the user picks up the phone). When the FXS is under Hot Line mode, no other
phone numbers can be dialed.

Hot Line No.:

Enter the number for pre-defined destination.

Warm Line:

Enter the time for the call to start with a pause, so the user can dial another number. The call

will be automatically directed to the pre-configured destination within timeout period.

FXS Group:

When there is an incoming call and the gateway will automatically assign an unassigned call

according to the Hunting Priority. If Port 2 does not want to be set as an assigned line to receive any
inbound calls, the function can be disabled.

Содержание GW-732FW























































































Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды

CTC Union GW-732FW, Руководство пользователя

Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды