CTC Union GW-732FW Скачать руководство пользователя страница 59

Страница: 59 / 86

Dual Band Wireless VoIP Gateway

User’s Manual

2-4-3 DTMF & PULSE

Advanced Settings

→

DTMF & PULSE

Dial Wait Timeout:

Enter the timeout duration after the user picks up the phone set.

Inter Digits Timeout:

Enter the timeout duration between the intervals of each key pressed. When

exceeding the set timeout duration without entering further digits, the numbers entered will be dialed out.

Minimum DTMF ON Length (Dial on)/ Minimum DTMF OFF Length (Dial off - between tones):

This

variable is to set the length of DTMF playback.

DTMF Detection Sensitivity:

This variable is to set the sensitivity of the telephone keys for the VoIP

Gateway to detect the DTMF.

DTMF Output Volume:

Adjust the Tx volume of FXS port for DTMF Caller ID or Out of Band DTMF.

Pulse Dial Mark/Space Ratio:

Duration and break of pulse dial ration.

FXS Pulse Detection:

It allows FXS detect PULSE dial method sends from a phone set.

Enable Out-of-Band DTMF:

This variable is to set the method of DTMF transmission. RFC2833 or SIP

Info.

Note:

Out-of-Band DTMF transport method varies from VoIP networks, please contact your VoIP

provider for the preferred method.

Enable Hook Flash Event:

Select

Auto

RFC2833

SIP info

for the signaling method of Hook Flash

Event.

Payload Type:

payload type of RFC2833.

Volume:

Select the volume of RFC 2833 from the drop-down menu.

Содержание GW-732FW























































































Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды

CTC Union GW-732FW, Руководство пользователя

Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды