CTC Union GW-732FW Скачать руководство пользователя страница 39

Страница: 39 / 86

Dual Band Wireless VoIP Gateway

User’s Manual

2-2-12 Calling Features

General Settings

→

Calling Features

Do Not Disturb:

Check the box to reject (busy tone played) incoming calls.

Unconditional Forward:

Check the box to forward incoming calls to the assigned

“Forwarding Number”

automatically.

Busy Forward:

Check the box to forward incoming calls to the

“Forward incoming Number” when the line is

busy.

No Answer Forward:

Check the box to forward incoming calls to the

“Forward incoming Number” after

ringing timeout (configurable from 10 to 60 seconds) expires.

Call Hold:

Check the box to hold the call on the specific FXS port.

Note:

Call Transfer or Call Waiting can only be activated when Call Hold is checked..

Call Transfer:

Check the box to transfer the call to another destination.

Call Waiting:

Check the box to accept incoming call while talking.

Three-Way Calling /Service ID:

It is for conference all based on Nortel Soft Switch and must work with

Proxy Server that supports Three-Way Calling service.

Local Mixer:

It is used to enable build-in conference service when ticked.

Содержание GW-732FW























































































Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды

CTC Union GW-732FW, Руководство пользователя

Результаты поиска

Содержание GW-732FW

Отзывы:

Похожие инструкции для GW-732FW

Бренды по названию

Популярные бренды