CSR Bradford SupaVent Скачать руководство пользователя страница 9

Страница: 9 / 16

Fix with supplied screws

Installation -

Tiled Roof

STEP 14

From within the roof

space, take the fixing strap

and bend it until it is in

a position to be securely

fixed to the lower tile

batten.

Screw (not supplied) the

fixing strap to the batten,

this will prevent the lower

part of the flashing lifting

in heavy winds.

Turning the top edge of the flashing upwards allows it to act as

a gutter to prevent any wind driven water from entering the roof

space.

Ensure the mounting points are properly secured on the top and

bottom ring of the varipitch.

Screw

Tile Batten

STEP 13

Position the ventilator

top onto the top of the

varipitch.

The three mounting

points on the lower ring

must align with the three

notches on the varipitch.

Fix the ventilator top to the

varipitch with the three

screws provided through

the pre-drilled holes.

Содержание Bradford SupaVent

















Результаты поиска

Содержание Bradford SupaVent

Отзывы:

Похожие инструкции для Bradford SupaVent

Бренды по названию

Популярные бренды

CSR Bradford SupaVent, Руководство по установке

Результаты поиска

Содержание Bradford SupaVent

Отзывы:

Похожие инструкции для Bradford SupaVent

Бренды по названию

Популярные бренды