Crystal Vision
Specification
M-VIVID User Manual R1.3
35
18 August 2022
Packet distribution is not important as variable input buffer will compensate for any timing
irregularities. Any traffic shaping option from ST 2110-21 can be used, or packets can come
from a device which does not meet the shaping requirement of ST 2110-21
A protect input for SMPTE ST 2022-7 seamless protection switching or the equivalent protect
input in ST 2110-20 can come from any of the 10GbE IP network interfaces. This protects the
video flow from lost packets by creating two streams of the same data using different routing
to the destination. IP packet analyser handles the analysis and reconstruction of the protected
video flow. Any IP input can come from any of the 10GbE IP network interfaces and can
either be multicast or unicast
SDI VIDEO OUTPUTS
(NB. Some or all of the outputs can be IP instead)
M-VIVID100-3:
Up to three 3Gb/s or HD or SD SDI outputs, one per channel
M-VIVID200-2 and M-VIVID400-2:
Up to two 3Gb/s or HD or SD SDI outputs, one per channel
M-VIVID800:
Up to one 3Gb/s or HD or SD SDI output
270Mb/s or 1.5Gb/s or 3Gb/s serial compliant to SMPTE 259, SMPTE 292-1 and SMPTE
424/425-A
IP OUTPUTS
(NB. Some or all of the outputs can be SDI instead)
M-VIVID100-3:
Up to three 3Gb/s or HD or SD video over IP outputs, one per channel
M-VIVID200-2 and M-VIVID400-2:
Up to two 3Gb/s or HD or SD video over IP outputs, one
per channel
M-VIVID800:
Up to two 3Gb/s or HD or SD video over IP outputs
Any of the 10GbE IP network interfaces can be used to provide a protected output for SMPTE
ST 2022-7 or ST 2110 seamless protection switching, which protects the stream from lost
packets by creating two streams of the same data using different routing to the destination
Alternatively it is possible to have a unicast on some network interfaces and a multicast on
others
RELAY BYPASS PROTECTION (SDI ONLY)
The VR07 frame rear module provides dual relay bypass protection when M-VIVID200-2, M-
VIVID400-2 and M-VIVID800 are used with both SDI inputs and SDI outputs
The relay bypass protection protects the video output on frame power failure or if the
MARBLE-V1 card loses power or is removed
An electromechanical relay switch on the VR07 needs power to hold the switch in one state
and will revert to the other state (card bypass) on loss of power. It prevents signal loss by
mechanically connecting an SDI input to an SDI output:
M-VIVID200-2:
SDI 1 In is connected to SDI 1 Out and SDI 2 In is connected to SDI 2 Out
M-VIVID400-2:
SDI 1 In is connected to SDI 1 Out and SDI 2 In is connected to SDI 2 Out
M-VIVID800:
SDI In is connected to SDI 1 Out
NB. Use of the VR07 requires issue 5 or later of MARBLE-V1
VIDEO FORMATS SUPPORTED
The video formats supported are 625i, 525i, 720p50, 720p59.94, 720p60, 1080i50,
1080i59.94, 1080i60, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50,
1080p59.94, 1080p60, 1080PsF23.98, 1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30,
2048x1080p23.98*, 2048x1080p24*, 2048x1080p25*, 2048x1080p29.97*, 2048x1080p30*,
