Crystal Vision CoCo104 Скачать руководство пользователя страница 20

Страница: 20 / 61

Crystal Vision

The CoCo Controller panel

CoCo104 User Manual R2.0

26/09/05

The following control menus are supported:

Control

Description

DEVICE

Show and/or search for connected CoCos

YUV GAIN

Adjust individual YUV gains/gain ratios

MENU

Accesses GPI On/Off, EDH On/Off, Device Label, Copy/Paste, ENG and Lock-
Panel sub-menus

SAVE

Save selected CoCo setup into temporary memory

RECALL

Recall panel setup from temporary memory to connected CoCo

UV PED/HUE

Adjust UV lift/pedestal and/or hue

CROP

Adjust vertical and horizontal crop

RGB PED

Adjust RGB lift/pedestal and/or hue

TIMING

Adjust horizontal delay and Y/C offset

WIPE/BYPASS

Set horizontal/vertical preview wipe and/or board bypass

LEGAL

Set RGB clipping On/Off and adjust RGB/YUV clipping threshold and slope

Note:

Yellow LEDs indicate when function buttons (F1 to F4) and the menu assignable shaft
encoder (under the CAL button) are active. The display always follows the last button or
menu accessed.

The following buttons are associated with panel menus and more advanced functions:

CoCo Controller panel – advanced control buttons

Each of these functions is discussed in detail in the controller operation section.

Using the split-screen (wipe) preview

The two AUX outputs are provided with the facility to perform a ‘before/after’
comparison of the corrections applied by CoCo104.

To use this facility, connect one of the AUX outputs to a monitor and press the
WIPE/BYPASS button.

Содержание CoCo104






























































Результаты поиска

Содержание CoCo104

Отзывы:

Похожие инструкции для CoCo104

Бренды по названию

Популярные бренды

Crystal Vision CoCo104, Руководство пользователя

Результаты поиска

Содержание CoCo104

Отзывы:

Похожие инструкции для CoCo104

Бренды по названию

Популярные бренды