Crystal Mountain Storm Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 33

background image

7 - 1

Scheduled cleaning and sanitizing is recommended to ensure the integrity of the drinking water.
The frequency of cleaning will vary depending on the conditions and environment.
Follow the steps outlined below for sanitizing the water cooler.

CAUTION: DO NOT IMMERSE THE UNIT IN WATER OR CLEAN USING PRESSURE WASHER.

1. Use latex or nitrile gloves or wash hands before and after handling water contact parts.
2. Remove drip tray assembly and set aside for cleaning (Figure 7-1).

3. Lift door up to open it properly (Figure 7-2). Turn off hot tank power switch (Figure 7-3) and unplug
the water cooler (Figure 7-4).

CAUTION: WATER IN HOT TANK IS VERY HOT AND CAN CAUSE SEVERE BURNS. ALLOW SUFFI-
CIENT TIME FOR THE HOT WATER TO COOL BEFORE DRAINING (1-2 HOURS).

4. Take water bottle out from its base. (Caution: don’t break the corrugated tube.) Remove the connector
from bottle adaptor (Figure 7-5).

Cleaning and Sanitization

Notice:
The information and/or procedures presented in the following demonstration(s) should be performed by a trained Water
Cooler Service Technician only.
Never attempt to service or repair a water cooler while it is plugged into any power supply.
Prior to any service or repair of the water cooler, ensure that the water has been completely drained from the system.

Figure 7-2 Figure 7-3 Figure 7-4

Figure 7-5

Figure 7-1

«
...
27
28
29
30
31
...
»

Содержание Storm


































Отзывы:

Нет отзывов

Похожие инструкции для Storm

Legend G3 738 NGK

Бренд: Valor Страницы: 6

Бренд: Pivot Страницы: 4

Бренд: Manfrotto Страницы: 36

Бренд: Baumer Страницы: 3

X-ACT CONTOUR 53491

Бренд: HUSKY LINERS Страницы: 2

Бренд: R&S Страницы: 44

Бренд: NuTone Страницы: 6

Silver Billet KR-800

Бренд: Havis-Shields Страницы: 1

Бренд: Ikelite Страницы: 4

Бренд: PROAIM Страницы: 3

Бренд: PCB Piezotronics Страницы: 17

Бренд: Acebil Страницы: 11

Бренд: Speaka Professional Страницы: 68

Бренд: YOKOGAWA Страницы: 24

Бренд: IFM Страницы: 5

Бренд: VARIZOOM Страницы: 3

Бренд: netvox Страницы: 13

Бренд: Dog & Bone Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды