Crystal Mountain Storm Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 33

background image

3 - 1

Replacement of

SmartFlo™ Water Cartridge

For the best tasting and highest quality water, it is recommended to change the SmartFlo™ Water Car-
tridge every 12 months. Follow the steps below to replace the SmartFlo™ Water Cartridge. It is recom-
mended to empty the bottle prior to replacement of the SmartFlo™ Water Cartridge and bottle adaptor.

Note: A flashing blue light above the cold water lever will alert you to when the SmartFlo™ Water Car-
tridge should be replaced. The system has been pre-set to provide indication after a period of 12 months
of use. User may operate the cooler as normal until the bottle has been emptied.

Note: To reset the life timer system, the SmartFlo™ is required to be removed from the dispenser for a
minimum of 15 seconds while the unit is connected to the mains power supply.

1. Open Dispenser door (Figure 3-1). (Slide door upwards to allow access to bottle area)

2. Slide empty bottle out of cabinet (Figure 3-2 and Figure 3-3).

3. Disconnect the water line from the bottle adaptor (Figure 3-4).

4. Open the replacement SmartFlo™ Water Cartridge kit, and remove the access key provided.

Notice:
The information and/or procedures presented in the following demonstration(s) should be performed by a trained Water
Cooler Service Technician only.
Prior to any service or repair of the water cooler, ensure that the water has been completely drained from the system.

Figure 3-1

Figure 3-4

Figure 3-2 Figure 3-3

«
...
7
8
9
10
11
...
»

Содержание Storm


































Отзывы:

Нет отзывов

Похожие инструкции для Storm

Бренд: Walimex Pro Страницы: 4

Бренд: Balboa Страницы: 2

Бренд: QUIETON Страницы: 24

Бренд: Quest Engineering Страницы: 24

Бренд: Nauticam Страницы: 2

Бренд: Garland Страницы: 36

Бренд: 4MOMS Страницы: 20

Бренд: Ecco Страницы: 4

Бренд: ICC Страницы: 32

Бренд: Parrot Страницы: 19

Бренд: Parrot Страницы: 88

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 11

CK 3000 Evolution

Бренд: Parrot Страницы: 8

CK 3000 Evolution

Бренд: Parrot Страницы: 106

Бренд: Varta Страницы: 2

Бренд: Eaton Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды