background image

7

III  Before Installing

1)  Safe, reliable operation of this boiler depends upon installation by a professional heating contractor in strict accordance 

with this manual and the requirements of the authority having jurisdiction. 

• 

In the absence of an authority having jurisdiction, installation must be in accordance with this manual and the latest 

edition of

 Installation of Oil Burning Equipment 

(ANSI/NFPA31).

• 

Where required by the authority having jurisdiction, this installation must conform to the latest edition of 

Standard for 

Controls and Safety Devices for Automatically Fired Boilers

 (ANSI/ASME CSD-1).

2)  Make sure that a properly sized chimney is available which is in good condition. Consult the authority having 

jurisdiction, Part VII of this manual, and

 

ANSI/NFPA31 for additional information on venting requirements. 

3) Make sure that the boiler is correctly sized. Use an industry accepted sizing method such as the 

I=B=R 

Guide RHH 

published by the Air-Conditioning, Heating and Refrigeration Institute (AHRI).

4) In some cases, boilers installed at altitudes above 2000ft may require a different burner configuration from that at sea level. 

Consult the local Crown representative for more information. 

TABLE 2.2: OPTIONAL TANKLESS 

HEATER RATINGS

MODEL

RATING (GPM)

KSB065

2.25

KSB075

2.25

KSB100

2.50

KSB125

2.75

KSB150

3.00

KSB175

3.25

KSB200

3.50

CAUTION

Fuel oil used with this boiler must conform to ASTM D396. The ASTM D396 standard sets a 

5% limit on biodiesel concentration, requires that the biodiesel feedstock comply with ASTM 

D6751, and also specifies the procedure that must be used to blend the biodiesel feedstock 

with the #2 fuel oil. Attempts to use biodiesel blends not meeting all ASTM D396 requirements 

may result in unreliable operation or severe property damage.

 

Tankless heater ratings based on 40F inlet water, 140F outlet water, and 190F

boiler water. Ratings are also based on 5 minute intermittent draws with 10 

minutes between draws.

Содержание KSB Series













































Отзывы: