Crestron iLux CLS-C6 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 92

Crestron iLux CLS-C6 Скачать руководство пользователя страница 41

Crestron

CLS-C6/C6M & CLSI-C6/C6M

iLux Integrated Lighting System

Operations Guide – DOC. 6347E

iLux Integrated Lighting System: CLS-C6/C6M & CLSI-C6/C6M

•

37

When the

Override

mode is disengaged, all loads revert to their previous values.

While in

Override

mode, all slave units are placed into

Override

mode as well,

regardless of the room combining status.
While in

Override

mode, all Cresnet commands (whether sent by a control

processor, or by a master iLux to a slave) shall be ignored, except for load level

commands, which cause the new final value to be stored and thus recalled when the

unit exits

Override

mode.

Override

mode levels take precedence over any limits set by

Load Shed

mode.

Load Shedding (Demand Response)

The iLux can enter a

Load Shed

mode via an external input (such as into a DIN-IO8

or GLS-SIM).
When entering

Load Shed

mode, any loads that must have their levels reduced shall

do so with a 1/2-second fade.
While in

Load Shed

mode, all loads must always be kept at or below their load shed

level (the only exception being

Override

mode).

When exiting

Load Shed

mode, loads that were commanded to go to a level below

their load shed level shall fade to the originally desired level in 1/2 seconds.
While in

Load Shed

mode, the 7-segment display shall flash "LS" at a rate of 1

second on, 1 second off, unless the display is actively showing something else.
Using iLux Designer, any value can be entered into the Load Shed Max field (0-

100%). The default Load Shed Max value in iLux Designer is 80% for all loads.

Building Management System (BMS) Interface

A DIN-IO8 unit is supported for the purpose of providing a contact-closure interface

to a Building Management System. A GLS-SIM is supported for the purpose of a

very basic contact-closure interface to a Building Management System.
The DIN-IO8 is required to have a designated Cresnet ID in order to work properly

in this capacity. The designated addresses are 0xD0 for normally open and 0xD1 for

normally closed DIN-IO8 types.
The functionality of the DIN-IO8 and/or GLS-SIM is fixed and cannot be changed

via

Setup

mode or iLux Designer.

The functionality provided by the DIN-IO8 is as shown in the following table:

DIN-IO8 BMS Functionality

PORT

FUNCTION

1

Recall On Scene (edge-triggered)

2

Recall Off Scene (edge-triggered)

3

Recall Scene 14 (edge-triggered)

4

Recall Scene 15 (edge-triggered)

5

Override

Mode (level-triggered)

6

Load Shed

Mode (level-triggered)

7

Defeat Occupancy. Sensors (level-triggered)

8

Lockout Front Controls (level-triggered)

Four unique Cresnet IDs are defined for the GLS-SIM to allow this unit access to the

following functions (2 per ID):·

•

Unit 1 (Cresnet ID 0xC5): Recall On/Off scene

«
...
39
40
41
42
43
...
»

Содержание iLux CLS-C6





























































































Отзывы:

Нет отзывов