Creative Playthings SH 6100-000 Скачать руководство пользователя страница 5

Страница: 5 / 24

YORKTOWN

19794-300 Rev J (05-20)

Page 5

HARDWARE / PRE-ASSEMBLY

50490-700 Hardware, Yorktown

5 14161-400 Access Ladder Bracket

1 50490-701 1/4" Hardware Bag

38 12002-205 Flat Washer 1/4"

21 17036-601 Lag Screw 1/4 x 1-1/2"

8 17036-1001 Lag Screw 1/4 x 2-1/2"

1 50490-702 Screw Bag

44 17020-106 Screw #8 x 1-5/8"

66 17020-112 Screw #8 x 2"

28 17020-113 Screw #10 x 2-1/2"

1 50490-703 5/16" Washer Bag

25 12002-206 Flat Washer 5/16"

20 12017-206 Lock Washer 5/16"

1 50490-704 5/16" Weld Nut Bag

20 17001-105 Weld Nut 5/16"

1 50490-705 5/16" Bolt Bag

2 17003-411 Hex Bolt 5/16 x 1"

7 17003-611 Hex Bolt 5/16 x 1-1/2"

3 17003-1411 Hex Bolt 5/16 x 3-1/2"

4 17003-1611 Hex Bolt 5/16 x 4"

10 17003-2211 Hex Bolt 5/16 x 5-1/2"

6 17036-1202 Lag Screw 5/16 x 3"

5 17036-2202 Lag Screw 5/16 x 5-1/2"

1 50490-706 3/8" Hardware Bag

2 12002-207 Flat Washer 3/8"

2 12017-207 Lock Washer 3/8"

3 17001-103 Weld Nut 3/8"

2 17003-2413 Hex Bolt 3/8 x 6"

1 50490-707 Screw Bag

66 17020-112 Screw #8 x 2"

1 50490-707 Hole Cap Bag

22 15081-704 1" Hole Cap

50334-700 Hardware Bag SP

2 14161-400 Access Ladder Bracket

1 50334-701 1/4" Hardware Bag

8 17001-104 Weld Nut 1/4"

4 12017-205 Lock Washer 1/4"

4 12002-205 Flat Washer 1/4"

4 17003-409 Hex Bolt -1/4 x 1"

4 17119-1209 Truss Head Bolt 1/4 x 3"

1 50334-702 5/16" Weld Nut Bag

66 17001-105 Weld Nut 5/16"

1 50334-103 5/16" Washer Bag

66 12017-206 Lock Washer 5/16"

84 12002-206 Flat Washer 5/16"

1 50334-704 5/16" Bolt Bag

4 17003-611 Hex Bolt 5/16 x 1-1/2"

8 17003-1011 Hex Bolt 5/16 x 2-1/2"

50 17003-1611 Hex Bolt 5/16 x 4"

4 17003-2211 Hex Bolt 5/16 x 5-1/2"

1 50334-705 Screw Bag

106 17020-105 Screw #8 x 1-5/8"

90 17020-112 Screw #8 x 2"

17 17020-107 Screw #10 x 2"

4 17020-113 Screw #10 x 2-1/2"

10 17036-1202 Lag Screw 5/16 x 3"

6 17036-1602 Lag Screw 5/16 x 4"

1 50345-100 Hole Cap Pack

94 15081-704 1" Hole Cap

50347-701 Hardware, Wood Roof

20 17001-105 Weld Nut 5/16"

20 12002-206 Flat Washer 5/16"

20 12017-206 Lock Washer 5/16"

10 17003-811 Hex Bolt 5/16 x 2"

4 17003-1611 Hex Bolt 5/16 x 4"

6 17003-1811 Hex Bolt 5/16 x 4-1/2"

4 17020-107 Screw #10 x 2"

1 50437-700 Hardware, Ridge Cap

18 17025-104 Screw #8 x 1-1/4"

9 17020-112 Screw #8 x 2"

50457-700 Hardware, Clubhouse

32 12002-206 Flat Washer 5/16"

8 15081-904 1" Hole Cap

24 17036-1002 Lag Screw 5/16 x 2-1/2"

10 17036-1202 Lag Screw 5/16 x 3"

We have packaged more hardware than is

required for assembly.

CREATIVE PLAYTHINGS PLAY SETS USE A FEW STANDARD CONNECTIONS. BECOMING FAMILIAR WITH THESE CONNECTIONS
WILL SIMPLIFY ASSEMBLY AND INSURE A SAFER PLAY PRODUCT FOR YOUR CHILDREN.

Hex Bolt & Weld Nut Assembly Procedure:

Typical Installation - Lag Screws:

• Tap the head of the Lag Screw with a

hammer to start the threads into the

wood and then use a socket to tighten.

• DO NOT over tighten

Typical Installation - Wood Screws:

•  Use an electric drill or screw gun to drive screws.
•  Drill pilot holes where needed.
•  We recommend to lubricate the threads of

the screws with beeswax or soap to mini-

mize breaking screws.

•

It is very important the tops of all screws

are flush with the surface of the wood

and there are no protruding sharp edges.

Assembly Layout:

Align the holes in the parts to be fastened. Start preliminary tightening of bolt into weld

nut by hand. Tighten each bolt with a wrench until the lock washer is fully compressed

between the head of the bolt and the flat washer.

Correct Assembly:

Bolt has been screwed securely into weld nut and the con-

nection is tight. Check connections periodically for tight-

ness during the life of the play set .

Do not over tighten.

Incorrect Assembly:

If, during assembly or maintenance the bolt protrudes 1/8" past

the weld nut, you may be overtightening or using the wrong

size bolt. Call customer service or replace the bolt at a local

hardware store.

Failure to replace this bolt with a shorter

one could result in serious injury.

All hardware on this set is specially coated for corrosion

resistance. If non-Creative Playthings hardware is used, it

MUST be galvanized or stainless steel.

Lag Screw

Flat Washer

Содержание SH 6100-000

























Результаты поиска

Содержание SH 6100-000

Отзывы:

Похожие инструкции для SH 6100-000

Бренды по названию

Популярные бренды

Creative Playthings SH 6100-000, Инструкция по сборке

Результаты поиска

Содержание SH 6100-000

Отзывы:

Похожие инструкции для SH 6100-000

Бренды по названию

Популярные бренды