Creative Playthings SH 6100-000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

background image

YORKTOWN

19794-300 Rev J (05-20)

© Copyright 2010, Creative Playthings

Page 17

ASSEMBLY INSTRUCTIONS

Step 20 — Roof Assemblies to Posts:

Note: The hardware to attach the Roof Assembly can be

found in the Roof Assembly Box. The Roof Assemblies (AG)

are heavy; be sure to have adequate assistance to position

and fasten each side.
Position the Roof Assemblies on the Corner Posts with the

holes at the top of the Corner Posts aligned with the holes in

the Roof Rafters. The angled end of the Roof Rafter should

be on the inside of the play set. Fasten each Roof Assembly

to the Corner Posts using two 5/16 x 4-1/2" Hex Bolt Assem-

blies. Do not tighten the fasteners completely until after the

next step.

Roof Rafter

Roof Rafter

Corner

Corner

Post

Post

Step 21 — Ceiling Joists:

Swing both Roof Assemblies until the ends touch. Adjust the

Roof Assemblies so the angled ends are even with each oth-

er. With the counter-bored holes facing out, fasten a Ceiling

Joist (AH) to the outside of the Roof Rafters on each side.

Use one 5/16 x 2" Hex Bolt Assembly in each end of each

Ceiling Joist.
Fasten the remaining Ceiling Joist to the Roof Rafters in the

center of the Roof Assemblies. Use a 5/16 x 2" Hex Bolt

Assembly in each end of the Ceiling Joist. Tighten the Bolts

holding the Roof Assemblies to the Corner Posts.

AG

AG

AH

Some Rafters

omitted for clarity

Step 22 — Panel Caps & Brackets:

Fit an Access Ladder Bracket into the notch on both Panel

Caps (AE). Fasten using 5/16 x 1" Hex Bolt Assemblies.
Fasten a Panel Cap to the top of the Double Window Panel

(AR) and the Door & Window Panel (AS) using four 1/4 x

2-1/2" Lag Screws and 1/4" Flat Washers each.
Pilot drill for each Lag Screw using a 1/8"

diameter drill.

AR

AE

AS

Bracket

«
...
15
16
17
18
19
...
»

Содержание SH 6100-000

























Отзывы:

Нет отзывов

Похожие инструкции для SH 6100-000

Бренд: Landoll Страницы: 6

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: Stiga Страницы: 20

Бренд: Stanton Страницы: 13

Бренд: habitat et jardin Страницы: 4

Бренд: Conrad Страницы: 34

Бренд: KUHN Страницы: 92

DRIP IRRIGATION KIT

Бренд: DAYLIFF Страницы: 2

Бренд: DANPHONE Страницы: 65

Challengers CH2727

Бренд: Playworld Страницы: 8

Бренд: KaVo Страницы: 20

Бренд: Rainbow Colour Changers Страницы: 16

Бренд: Aseptico Страницы: 20

CMC/Roco Cobra Rescue Harness

Бренд: CMC Rescue Страницы: 2

Бренд: P.Lindberg Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды