Creative Playthings NEWBURY Скачать руководство пользователя

Страница: 16 / 18

NEWBURY
19963-100 Rev C (05-20)

Page 16

ASSEMBLY INSTRUCTIONS

STEP 21 – Side & Back Wall Slats:

Evenly space six Wall Slats (N) between the swing side

Post Assemblies.

Hold the Wall Slats 1/2" above the Deck

Boards.

Fasten each Wall Slat to the back tent support and

the platform support using four #8 x 1-5/8" Screws. The gap

will be approximately 2-3/8" between slats.

STEP 22 – Climber Slats and Slide Slats:

Fasten two Wall Slats (N) to the climber side tent support

and platform support using four #8 x 1-5/8" Screws each as

shown. Leave a maximum of 3-1/4" between each Wall Slat

and the adjacent post.

Hold the Slat 1/2" above the Deck

Boards.

Place two Entrance Slats (O) just less that 3-1/2"

from the Post Assemblies on either side of the

access ladder.

Hold the Wall Slats 1/2" above

the Deck Boards.

Fasten each Slat to the platform

support and the wall support using four #8 x 1-5/8"

Screws. The gap will be approximately 24-1/2"

between slats.

1/2" gap

below all

Slats

Parts omitted

for clarity.

Parts omitted

for clarity.

1/2" gap

below all

Slats

< 3-1/2" typical

2-3/8" typical

2-1/2" typical

Fasten two Wall Slats (N) to the slide side tent

support and platform support using four #8 x

1-5/8" Screws each as shown. Leave a maxi-

mum of 2-1/2" between each Wall Slat and the

adjacent post.

Hold the Slat 1/2" above the

Deck Boards.

Climber

Side of the

Gym

3-1/4" typical

Swing side

of the gym

25"

STEP 20 – Swing Mount and Safety Rail:

Secure the Swing Mount (AG) to the Tent and Platform

Supports on the swing side of the gym using two 5/16 x

4-1/2" Hex Bolt Assemblies.
Mark the swing side Posts 25" above the ground. Align the

top edge of the Safety Rail (D) with the marks. Drill 1/4"

diameter pilot holes into the posts and secure the Safety

Rail using two 5/16 x 3-1/2" Lag Screws and Flat Washers.

Содержание NEWBURY


















Результаты поиска

Содержание NEWBURY

Отзывы:

Похожие инструкции для NEWBURY

Бренды по названию

Популярные бренды

Creative Playthings NEWBURY, Инструкция по сборке

Результаты поиска

Содержание NEWBURY

Отзывы:

Похожие инструкции для NEWBURY

Бренды по названию

Популярные бренды