Creative Playthings NEWBURY Скачать руководство пользователя

Страница: 18 / 18

NEWBURY
19963-100 Rev C (05-20)

Page 18

ASSEMBLY INSTRUCTIONS

STEP 26 – Slide:

Position the Slide (AJ) onto the Slide Mount through the

opening prepared in earlier steps. Center the Slide in the

opening and pull it tight to the platform until it stops against

the edge of the platform. Make sure the holes in the Slide

are over the Slide Mount.
Ensure the Slide extends out perpendicular from the Playset.
Drill 5/16" holes through the Slide, Slide Mount, and Platform

Boards using the holes in the Slide as a guide. Fasten the

slide using one 1/4 x 3" Truss Head Bolt and one 1/4" Weld

Nut for each hole.

Note: Depending on the Slide, you may find the holes you

drill encounter a framing member. If so, stop drilling after

piercing the Platform Board. Loosen the Platform Board

and insert the Weld Nuts from the underside. If desired, a

1" spade drill bit can be used to clear a space for the base of

the Weld Nut in the framing member. Re-attach the Platform

Board and continue attaching the Slide.

STEP 27 – Swing Beam & Swings:

Install the Swing Beam as instructed by the assembly guide

included with the Beam.
Hang the Swings and Ring Trapeze in the positions shown

at right.
U.S. safety standards require a minimum clearance of 8"

from the bottom of each Swing Accessory to the ground. U.K.

(& E.U.) safety standards require a minimum clearance of

350mm (13-3/4") between the bottom of each Swing Acces-

sory and the ground.
The height of each Swing Accessory is adjusted by using a

different link in the chain. Be sure to hang the Swings Ac-

cessories with ground clearance greater than or equal to the

safety standard for your region.

STEP 28 – Ground Stakes:

Hammer Ground Stakes next to the Beam Legs as shown.

Secure each stake with two #8 x 2-1/2" Screws through the

pre-drilled holes.

Note: Do NOT use concrete to set Ground Stakes. Pound a

metal spike or rod into the ground to start a hole in hard or

rocky ground.

Save all instruction sheets and receipts in case it becomes necessary to contact

Creative Playthings for warranty service and/or part replacement. The warranty

can be found in your Owner’s Manual.

Содержание NEWBURY


















Результаты поиска

Содержание NEWBURY

Отзывы:

Похожие инструкции для NEWBURY

Бренды по названию

Популярные бренды

Creative Playthings NEWBURY, Инструкция по сборке

Результаты поиска

Содержание NEWBURY

Отзывы:

Похожие инструкции для NEWBURY

Бренды по названию

Популярные бренды