background image

John Deere Air Reel Owner’s Manual

1

LiMiTED WARRANTY

This warranty applies to all AG and Outdoor Power Equipment manufactured by Crary Industries.

Crary Industries warrants to the original owner each new Crary Industries product to be free from defects 
in material and workmanship, under normal use and service. The warranty shall extend 1 year from date of 
delivery for income producing (commercial) applications and 2 years from date of delivery for non-income 
producing (consumer) use of the product. The product is warranted to the original owner as evidenced by a 
completed warranty registration on file at Crary Industries. Replacement parts are warranted for (90) days 
from date of installation.

THE WARRANTY REGiSTRATiON MUST bE cOMPLETED AND RETURNED TO cRARY iNDUSTRiES 
WiTHiN 10 DAYS OF DELivERY OF THE PRODUcT TO THE ORiGiNAL OWNER OR THE WARRANTY 
WiLL bE vOiD.

 

In the event of a failure, return the product, at your cost, along with proof of purchase to the selling Crary 
Industries dealer. Crary Industries will, at its option, repair or replace any parts found to be defective in material 
or workmanship. Warranty on any repairs will not extend beyond the product warranty.  Repair or attempted 
repair by anyone other than a Crary Industries dealer as well as subsequent failure or damage that may occur 
as a result of that work will not be paid under this warranty.  Crary Industries does not warrant replacement 
components not manufactured or sold by Crary Industries.

This warranty applies only to parts or components that are defective in material or workmanship.  

This warranty does not cover normal wear items including but not limited to bearings, belts, pulleys, filters 
and chipper knives.

This warranty does not cover normal maintenance, service or adjustments.

This warranty does not cover depreciation or damage due to misuse, negligence, accident or improper 
maintenance.

This warranty does not cover damage due to improper setup, installation or adjustment.

This warranty does not cover damage due to unauthorized modifications of the product. 

Engines are warranted by the respective engine manufacturer and are not covered by this warranty.

Crary Industries is not liable for any property damage, personal injury or death resulting from the unauthorized 
modification or alteration of a Crary product or from the owner’s failure to assemble, install, maintain or operate 
the product in accordance with the provisions of the Owner’s manual.

Crary Industries is not liable for indirect, incidental or consequential damages or injuries including but not 
limited to loss of crops, loss of profits, rental of substitute equipment or other commercial loss.

This warranty gives you specific legal rights.  You may have other rights that may vary from area to area.

Crary Industries makes no warranties, representations or promises, expressed or implied as to the performance 
of its products other than those set forth in this warranty.  Neither the dealer nor any other person has any 
authority to make any representations, warranties or promises on behalf of Crary Industries or to modify the 
terms or limitations of this warranty in any way.  Crary Industries, at its discretion, may periodically offer limited, 
written enhancements to this warranty.

cRARY iNDUSTRiES RESERvES THE RiGHT TO cHANGE THE DESiGN AND/OR SPEciFicATiONS 
OF  iTS  PRODUcTS  AT  ANY  TiME  WiTHOUT  ObLiGATiON  TO  PREviOUS  PURcHASERS  OF  iTS 
PRODUcTS.

1.

2.

3.

4.

5.

6.

7.

Содержание JOHN DEERE 200













































































Отзывы: