Crane BevMAX Refresh 4 3800-4 Скачать руководство пользователя страница 55

Страница: 55 / 62

Page 55 of 62

MACHINE NOT COOLING

Condenser Fan or

Evaporator Fan

not running.

Evaporator is iced

up.

Clean Condenser.

Replace Encapsulated Temp. Sensor.

Machine not

cooling.

Dirty or clogged

Condenser.

Clear Rear Screen of obstructions. Ensure rear

of Cabinet is at least 4” (10cm) from wall.

Defective

Encapsulated

Temp. Sensor.

Move Machine.

Machine in direct
sunlight or near a

heat source.

Replace faulty seal(s).

Restricted airflow.

Check Fan Blades for obstruction. Check Fan circuit.

134a - Replace as necessary.

R290 – Replace the Refrigeration Deck and return it

to Crane

Check for air leaks or clogged Condensate

drain.

Move Machine.

Machine in location

with humidity

above 70%.

Faulty Product

area seal(s).

Содержание BevMAX Refresh 4 3800-4































































Результаты поиска

Содержание BevMAX Refresh 4 3800-4

Отзывы:

Похожие инструкции для BevMAX Refresh 4 3800-4

Бренды по названию

Популярные бренды

Crane BevMAX Refresh 4 3800-4, Руководство по эксплуатации

Результаты поиска

Содержание BevMAX Refresh 4 3800-4

Отзывы:

Похожие инструкции для BevMAX Refresh 4 3800-4

Бренды по названию

Популярные бренды