Crane BevMAX Refresh 4 3800-4 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 62

background image

Page 14 of 62

VENDING MACHINE CONTROLLER & 5 PERIPHERAL CABINET CONTROLLERS

VMC (Vending Machine Controller)

is the heart of the Vender and is located on the Service

Door just above  the  Port Assembly behind the  Keypad.  It is USB flash programmable and
updates  all  peripheral  Cabinet  Control  Boards  which  control  all  aspects  of  the  Vender
(includes AC Distribution Box Cabinet Control Environmental Board, Cabinet Control X Motor
Board, Cabinet Control Y Motor Board, Cabinet Control Port Board, & Cabinet Control Cup
Board).  The VMC includes 7 Diagnostics lights providing information on operational status
and  where  to  focus  problem  solving  efforts.    All  voltage  in  the  VMC  and  Cabinet  Control
Boards is 24VDC or 5VDC.

Cabinet Control Environmental Board

– controls the Refrigeration Unit & Condenser Fan,

Evaporator Fan, LED Lighting, Encapsulated Temp Sensor, and 24VDC & 5VDC power
distribution.

Cabinet Control X Motor Board

– controls X Motor movement and sense the X Home

Switch Signal.

Cabinet Control Y Motor Board

– controls Y Motor movement and senses the Y Home

Switch signal.

Note: The Cabinet Control X & Y Motor Board are the same Board but with their own specific software.

Cabinet Control Port Board

– controls the Port Vend Sensor, Port Open & Close

Sensors, & the Port Motor.

Cabinet Control Cup Board

– controls the Delivery Cup Sensor, Picker/Plunger Home &

Out Switches, and the Cup Motor. The Y Home Switch plugs into the Cup Motor Board
and sends the switch signal on to the Cabinet Control Y Motor Board.

Each of the 5 Cabinet Control peripheral Boards have a Green status light. Various lighting patters are used to
indicate the status of the individual Cabinet Control Boards. They include:
Power on / Reset – a slow brightening and then slow diming of the Green status light that takes 3 to 5 seconds to
complete. This happens once each time the Board is powered on and/or reset. If the Green status light slowly
brightens and dims continuously indicates the software was not loaded properly.

«
...
12
13
14
15
16
...
»

Содержание BevMAX Refresh 4 3800-4































































Отзывы:

Нет отзывов

Похожие инструкции для BevMAX Refresh 4 3800-4

INSIDE-FOG FLUID

Бренд: Safex Страницы: 8

Бренд: UnionSpecial Страницы: 44

Бренд: Sega Страницы: 129

Бренд: JUKI Страницы: 15

LBH-1790A Series

Бренд: JUKI Страницы: 5

Бренд: JUKI Страницы: 33

Бренд: Saeco Страницы: 36

SAECO D.A. 10P Instant

Бренд: Saeco Страницы: 84

Бренд: Chauvet Страницы: 20

Бренд: Singer Страницы: 24

Бренд: Singer Страницы: 18

Бренд: Singer Страницы: 31

Бренд: Singer Страницы: 32

Бренд: Riccar Страницы: 26

Бренд: Riccar Страницы: 26

Бренд: Riccar Страницы: 64

FAST 02 2C PRO PLUS

Бренд: UR FOG Страницы: 24

Бренд: StepRevolution Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды