Snack / Refreshment Center Setup and Operator's Guide
Page 13
1670001
April, 1999
These instructions will guide you through setting up your trays for vending. You will be asked to deter-
mine if your tray can physically hold the products you intend to vend. If not, you will be directed to other
procedures which will help you get them set up. Follow these nine steps for each tray in your machine:
1.
Make sure the tray is in the loading position.
2.
Is the column wide enough for the intended product? If so, proceed to the next step. Otherwise,
set up your tray to vend wider products (see below, this page). When you' re done, return to step 3
in this procedure.
3.
Will the products fit between the spiral turns? If so, proceed to the next step. Otherwise, change
the spiral.
4.
Will the product pass under the tray immediately above? If so, proceed to the next step. Other-
wise, reposition the tray and guides.
5.
Will the product touch products on either side? If not, proceed to the next step. Otherwise, install a
product spacer.
6.
Load products in the tray.
7.
Return the tray to the vending position.
8.
Install the price rolls.
9.
Install the selection ID numbers.
The following steps will help you configure your tray to vend wide products. When you have completed
the procedures called out in each step, return to the next step in the procedure. When you are done with
the entire wide product steps, return to the set-up procedures above.
1.
Remove the tray from the merchandiser and place on a flat surface.
2.
Based on the size of the product you want to vend, decide how many spiral positions it will occupy.
Please remember that the leftmost spiral in the group
must
have an even ID number (0, 2, 4, etc.)
For example, if a product is three spirals wide, the left spiral will be ID number 0, and the right spiral
will be ID number 2. Be careful how wide you set up for, because really wide products could get
hung up in the delivery door.
3.
Remove the column dividers inside the group. In the example of three spiral positions, you would
be removing the dividers between spiral ID numbers 0 and 1, and 1 and 2.
4.
If your group only consists of 2 spirals, replace the rightmost motor with a spiral bearing and gear,
and install a gear on the leftmost motor. Skip to step 8.
5.
Remove all spirals in the group except the leftmost spiral.
6.
Do one of the following:
!" #$%&'()%*)'(+%,!-%!.%
'11
%.(/01)%'$%-+2)!3-%456%76%189":%)1/';1%8,1%,!).1--1-%$)'/%!33%/'8')-%2.
8,1%*)'(+%1<91+8%8,1%31$8/'-8%'.1"%%='%8,1%)2*,8/'-8%/'8')6%9'..198%8,1%,!).1--%$)'/%8,1%/'8')
2//1>2!813&%8'%28-%31$8"
0" #$%&'()%*)'(+%,!-%!.%
$2$")
.(/01)%'$%-+2)!3-%4?6%@6%189":%)1/';1%8,1%,!).1--1-%$)'/%!33%/'8')-
345367
%8,1%*)'(+%431!;1%8,1%,!).1--1-%9'..1981>%8'%8,1%31$8/'-8%!.>%)2*,8/'-8%/'8')-:"
7.
Install a spiral at the rightmost position in your group. Make sure it has the same product capacity
and is opposite to the one in the leftmost position.
8.
Return the tray to the merchandiser.
9.
Electronically couple the motors as needed (see your
Programming Guide
for information).
10. Return to step 3 in the
Set Up Trays to Vend Products
procedure, above.
GB&&L$-&/0&=%1F.&-"&M$,8&!%"8)2-.
L$-&/0&J&=%1F&="&M$,8&N*8$&!%"8)2-.
Содержание 787E
Страница 2: ......