CRAFTOP NT3760, Руководство пользователя

Страница: 19 / 53

|
-16-
Before starting the engine
A area within a minimum radius of 50feet (15m) from
the using the machine should be considered as a
hazardous area, into which on one should enter. If
necessary, yellow warning rope and warning signs
should be placed around the perimeter of the area.
When work is to be performed simultaneously by two or
more persons, special care should also be taken to
constantly look around or otherwise check for the
presence and locations of other people working, so as
to maintain sufficient safety distance between each
person.
Before starting the engine, take off the chain guard
(scabbard), and check that your machine is properly
assembled and in good condition
•
Check cutting equipment is correctly fitted and
adjusted.
•
Check the fuel system for leaks, paying high attention
to visible parts such as the fuel tank cap, hose
connections and the manual fuel pump (if equipped).
If there are any leaks or damage, do not start the
engine because of potential risk of fire. Have your
machine repaired by an authorized dealer or service
center before using it again.
•
The engine stop switch must move easily in direction
of STOP position and spring back to the normal
START position.
•
Smooth action of throttle trigger lockout and throttle
trigger - The throttle trigger must return automatically
to the idle position by itself.
•
Check that the spark plug boot is secure – a loose
boot may cause arcing that could ignite combustible
fumes and cause a fire.
•
Saw chain securely mounted and in good condition
(clean, move freely, not warped, properly sharpened).
•
Never attempt to modify the controls or safety devices
in any way.
•
Keep all handles dry and clean, free from oil and dirt
– for safe control of the machine.
•
To reduce the risk of accidents, do not operate your
machine if it is damaged or not properly assembled.
When starting the engine
WARNING
Note that the saw chain continue to run for a short
period after you let go of the throttle trigger, due to
flywheel effect.
•
Start the engine at least 10feet (3m) from the fueling
spot, outdoors only.
•
Keep bystanders, especially children and animals at
least 50feet (15m) from the operating point. If you are
approached, immediately stop the engine.
•
Place the machine on firm ground in an open and well
ventilated area. Make sure you have good balance
and secure footing. Hold the machine securely. The
saw chain must not contact the ground and all other
obstructions because they may begin to run when the
engine starts.
•
Your machine is designed to be operated by one
person only. Do not allow other persons in the work
area even when starting.
•
To reduce the risk of injury, avoid contact with the
saw chain.
•
Do not drop start the power tool, just follows the way
and start the engine as described in this manual.
•
Never start the engine by standing on the cutting
attachments side.
•
Check idle speed setting: The saw chain must not
move when the engine is idling with the throttle trigger
released. If it continues to move even after the throttle
trigger has been completely released, shut off the
engine and take the machine to your authorized
dealer or service center for inspection and/or repair.
information
When a new machine is first operated, in the first few
minutes grease may come out of the gear case. But,
since this is excessive grease, there is no cause of
alarm. Just wipe it off with the engine stopped for next
use
During operation
WARNING
Moving parts can amputate fingers or cause severe
injuries. Keep hands, clothing and loose objects away
from all moving parts. Always stop engine, disconnect
spark plug, and make sure all moving parts have come
to a complete stop before removing obstructions,
clearing debris, or servicing unit.
Do not touch any moving parts,
especially the saw chain, while the
motor is running. If the saw chain
become jammed by thick branches
or other obstructions, switch off the
engine immediately before
attempting to free the saw chain –
there is otherwise a risk of injury.
Hot surface.
Do not touch.
•
Always carry related tools, equipments, spare parts,
and consumables with you:
-
Attached tools in the product package.
-
Personal protective equipments.
-
Properly reserved fuel
-
Spare parts.
-
Things to notify your working are (rope, warning
signs, etc.).
-
Whistle (for collaboration or emergency).
-
Hatchet or saw (for removal of obstacles).
•
Check that there are no bystanders, children, and
animals in the general work area. If someone comes:
-
Guard against hazardous situations at all times.
Warn adults to keep children and pets away from