background image

page 5

5. Fan Assembly. (cont.)

With the hanging bracket secured to the outlet 
box and able to support the fan, you are now 
ready to hang your fan. Grab the fan firmly with 
two hands. Slide downrod through opening in 
hanging bracket and let hanging ball rest on 
the hanging bracket. Turn the hanging ball slot 
until it lines up with the hanging bracket tab.

WARNING

: Failure to align slot in hanging ball 

with tab in hanging bracket may result in 
serious injury or death.

Tip

: Seek the help of another person to hold 

the stepladder in place and to help lift the fan 
up to you once you are set on the ladder. 

Find a secure attachment point (wood ceiling 
joist highly recommended) and secure safety 
cable. It will be necessary to use a heavy duty 
wood screw, washer and lock washer (not 
supplied) with the safety cable loop. If 
necessary, adjust the loop at the end of the 
safety cable. The loop at the end of the safety 
cable should just fit over the threads on the 
wood screw. 

Test safety cable by pulling on loose 

end with pliers. If the safety cable slips, the loop 
must be adjusted tighter. 

Extra cable slack can be 

left in ceiling area.

Thread safety cable and wires through hanging ball; 
then slide hanging ball over downrod--the top of the 
downrod should be noted as having a set screw hole; 
use this hole when setting the set screw. Insert stop pin 
into top of downrod and raise hanging ball. Be sure 
stop pin aligns with slots on the inside of the hanging 
ball. Tighten set screw securely. [

Refer to 

diagram 4

.

Lower weatherproof yoke cover to motor housing.

Remove electrical tape from electrical wiring and 
thread each of the wires through a different hole in the 
weatherproof hanging ball cover.  Thread the safety 
cable with the green (ground) wire.  Pull weatherproof 
hanging ball cover down securely over hanging ball (on 
downrod). [

Refer to 

diagram 4

.

]

WARNING

: Failure to tighten set screw on hanging ball 

completely could result in the fan becoming loose and 
possibly falling.

hanging ball slot

hanging bracket tab

motor housing

safety cable

wood screw

and washer

safety cable loop

wood

ceiling

joist

canopy

diagram 4

set screw hole

set screw

hanging ball

yoke cover

canopy

motor housing

stop pin

safety cable

weatherproof 

hanging 

ball cover

electrical wiring

downrod

accessory

Содержание Union UN52-LED



























Отзывы: