Craftex CX125 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 34

Craftex CX125 Скачать руководство пользователя страница 22

22

4.

Undo and remove the (6) M6-1x16 cap
screws using the supplied 4mm hex
wrench from the gib.

5.

Once screws are removed from the gib
remove the gib using supplied magnets
then remove the knives.

Inspecting Cutterhead Assembly

1.

Make sure machine has been
disconnected from the power supply.

2.

Clean the cutterhead carefully with a
shop rag. Once clean check for the
following with a flashlight for better
visability.

Check for buildup of glue or resin

on the cutterhead, gib, and knives.
Remove all glue and resin so the
knives and gib will sit flat on the
cutterhead.

Check knives for any cracks, chips,

or damage. If one knife is damaged
you should replace both as a set.

Check and make sure that the

threaded screw holes contain no
sawdust or debris.

Check and make sure the hex

sockets and screw heads are all in
good condition. Replace any that
may appear worn.

Replacing Knives

1.

Make sure the machine has been
disconnected from its power source.

2.

Using the supplied magnets to position
the knife over the two pins on the
cutterhead. Make sure that the
orientation of the knife is such that the
beveled edge is up.

3.

Again using the supplied magnets place
gib over the knife. Fasten the gib
securely using the (6) M6-1x16 cap
screws.

4.

Rotate the cutterhead carefully until the
other knife slot is visible and then repeat
steps 2 and 3. Finally replace the knife
guard when finished.

Replacing or Adjusting Tension on
V Belt

The cutterhead assembly is driven by a belt
that is located on the right side of the
planer. Over time even though the belt is
strong and durable it may begin to stretch
and slip signaling a need to be adjusted or
even replaced.

1.

Make sure that the machine has been
disconnected from its power supply.

2.

Remove dust port and fan housing from
the machine by undoing and removing
the (5) M5-.8x15 tap screws.

«
...
20
21
22
23
24
...
»

Содержание CX125



































Отзывы:

Нет отзывов