Craftex CX125 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 34

Craftex CX125 Скачать руководство пользователя страница 20

20

MACHINE MAINTENANCE

NOTE

Before any maintenance is to be performed
you

MUST unplug machine from the

power supply

to prevent any accidental

startups and risk of electrical shock.

Maintenance

In order to ensure optimal performance
from your machine please follow the
following maintenance steps:

You should check things like

damaged knives, If the mounting
bolts are loose, and look for worn
or damaged wires daily before
operation of machine.

Once a month you should remove

any dust or debris from chains and
sprockets. Then lightly coat the
chains and sprockets with bearing
grease.

Check the V belt tension once a

month also inspect for damage or
wear on the belt.

Once a month while the machine is

disconnected from the power
source remove the cutterhead
guard and fan cover to remove all
dust and debris that have built up
from regular use of the machine.

LUBRICATION

Always clean all dust and debris from roller
chain drive, table height chain drive, and
the lead screw for the cutterhead height
adjustment before applying any kind of
lubricant.

To Lubricate Height Adjustment
Lead Screw:

1.

Always disconnect machine from power
source.

2.

Clean all parts thoroughly until they are
clear of any dust and debris using
mineral oils

3.

Apply lubricant onto all four lead screws
then use the cutterhead height
adjustment crank to move the
cutterhead up and down to help
distribute the lubricant evenly.

To Lubricate Table Height
Chain/ Feed Roller Drive Chain:

1.

Always make sure the machine is
disconnected from the power supply.

2.

Carefully rest the planer on its side to
gain access to the table height chain.

«
...
18
19
20
21
22
...
»

Содержание CX125



































Отзывы:

Нет отзывов