12
13
INSTALLATION INSTRUCTIONS
IMPORTANT
: This appliance SHALL BE installed only by qualified technician and in accordance with the
manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, electrical wiring
regulations, local water supply regulations�
REMOVING PACKAGING MATERIALS
WARNING
: Excessive Weight Hazard
• Use two or more people to move and install range�
• Failure to do so can result in back or other injury�
1�
Remove all packaging materials, tape, and film from the range� Keep cardboard bottom under range� DO
NOT dispose of anything until the range installation is complete�
2�
Remove all oven racks and parts packaged from the range�
3�
To remove the cardboard bottom�
a�
Take 4 cardboard corners from the carton�
b�
Stack one cardboard corner on top of another� Repeat with the other 2 corners�
c�
Place the stacked corners lengthwise on the floor behind the range to support the range when is laid
on its back�
4�
Using two or more people, firmly grasp the range and gently lay it on its back on the cardboard corners�
5�
Remove cardboard bottom�
NOTE
: It is recommended to adjust leveling legs while the range is on its back�
NOTE
: To place range back up into standing position
• Place a sheet of cardboard or hardboard on the floor in front of range to protect the flooring�
• Using two or more people, stand the range back up onto the cardboard or hardboard�
HOW TO INSTALL BACKSPLASH
NOTE
: For proper ventilation and to protect your wall from splatter, install the backsplash to the rear edge of
the cooktop to which extends past the back of the oven�
NOTE
: 4 Screws are provided with the range�
1�
Align the holes in the backsplash with the holes in the back edge of the cooktop�
2�
While one person is holding the backsplash in the correct place, have the second person insert screws
through the bottom of the cooktop into the bottom of the backsplash�
3�
Tighten completely�
HOW TO INSTALL ANTI-TIP BRACKET
NOTE
: An anti-tip bracket kit is provided with the range�
WARNING
: Tip Over Hazard
• A child or adult can tip the range and be killed�
• Connect anti-tip bracket to rear range foot�
• Reconnect the anti-tip bracket, if the range is moved�
• Failure to follow these instructions can result in death or serious burns to children and adults�
IMPORTANT
: DO NOT completely remove the rear leveling leg� The anti-tip bracket uses either the right-hand
or left hand, rear leveling leg to secure the range to the floor�
Figure 10
Figure 11
STEP 1: LOCATE THE BRACKET
Determine the final location of the range before attempting to install the bracket�
1�
Place the bracket on the floor with the back edge against the rear wall� If the range does not reach the rear
wall, align the back edge of the bracket with the rear panel of the range in its final location�
NOTE
: If bracket does not touch the rear wall, you MUST screw bracket to FLOOR as described in Step 2�
2�
Position the side of the bracket against either the left or right cabinet� If there is no adjacent cabinet, align
the edge of the bracket with the side panel of the range in its final location� If the countertop overhangs
the cabinet, offset the bracket from the cabinet by the amount of overhang�
3�
Mark the location for the pair of holes to be used (see illustration above)�
NOTE
: For FLOOR installation use either Loc A or B� For REAR WALL installation use Loc C�
STEP 2: SECURE THE BRACKET
The bracket must be screwed to either the FLOOR or REAR WALL�
FLOOR Installation:
•
WOOD FLOOR: Use the screws provided to secure the bracket using the pair of marked holes (either Loc A or B)�
•
CONCRETE FLOOR: Using a concrete bit, drill a 5/32” pilot hole 2” deep into the concrete at the center of
each of the marked holes (either Loc A or B)� Use the screws provided to secure the bracket into the floor�
REAR WALL Installation: Use the 2 screws provided to secure the bracket using the pair of marked holes at Loc C�
The screws MUST enter into a wood sill plate� If the wall contains any metal studs or similar materials, then the
floor must be used�
Adjacent cabinet
or final location
of range side panel
Loc A
Loc B
Loc C
Rear Wall
Attachment to Floor or Rear Wall
Wall Sill Plate
Screw must enter wood
Two screws must
enter floor or wall
at Loc A, B, or C�
Bracket
Screw must enter
wood or concrete
STEP 3: CHECK THE BRACKET
After installing the bracket, slide the range into its final location� The rear leveling leg must be fully inserted
into the ANTI-TIP bracket as shown in Step 1� To check if the bracket is installed and engaged properly, look
underneath the range to see that the rear leveling leg is engaged in the bracket� On some models, the storage
drawer or kick panel can be removed for easier inspection� If visual inspection is not possible, slide the range
forward, confirm the anti-tip bracket is securely attached to the floor or wall, and slide the range back so the
leveling leg is under the anti-tip bracket� If the range is pulled from the wall for any reason, always repeat this
procedure to verify the range is properly secured by the anti-tip bracket�
NOTE
: The anti-tip bracket must be PROPERLy INSTALLED and the rear leveling leg must be FULLy ENGAGED
into the bracket to prevent the range from tipping� NEVER remove the leveling legs� This will prevent the range
from being secured to the ANTI-TIP bracket properly�
INSTALLATION INSTRUCTION
