![Cosen C-325NC Скачать руководство пользователя страница 62](http://html1.mh-extra.com/html/cosen/c-325nc/c-325nc_instruction-manual_2670350062.webp)
OPERATING INSTRUCTION
SECTION 4
4-25
4.6.3 Adjusting saw arm
Adjust the blade guide (guide arm) position based on the size of your workpiece:
Step 1 –
Loosen the inserts by unlocking the lock nut.
Step 2 –
Loosen the blade guide locking handle. Then adjust the guide arm to a position suitable for
your workpiece size.
Step 3 –
After adjustment is made, tighten the blade guide locking handle.
Note: When tightening the blade guide locking handle, gently shake the lower end of the blade guide
so that the dovetail fixed block behind is properly aligned.
Step 4 –
Clamp the inserts back by tightening the lock nut.
4.6.4 Placing workpiece onto workbed
Step 1 –
Press the saw bow up button and elevate the saw bow until it reaches to its highest point.
Step 2 –
Press the front vise open and rear vise open buttons to open vises.
Step 3 –
Loosen the vertical roller lock handles and fully open the vertical rollers.
Step 4 –
Carefully place the workpiece onto the work feed table to where it extends approximately
30mm(1.2 inch) beyond the rear vise toward the front vise.
Locking Handle
Inserts Lock Nut
Содержание C-325NC
