CORNING SCF-6 Скачать руководство пользователя страница 4

Страница: 4 / 32

SCF-6 Canister and Inline Splice Closures

Page 4

SRP 003-485 • Issue 6 • October 2006

CARTON CONTENTS

2.1

SCF-6C Closure Contents

•

(1) Tray stacker (Two in -02 configurations)

•

(1) Dome cover

•

(1) End cap

•

(2) M8x14 Hex bolts

•

(1) Clamping ring

•

(1) Sealing ring

•

(1) Frame assembly

•

(1) Slack basket (none in -02 configurations)

•

(1) Accessory kit (p/n SCF-6C-ACCY)

•

(2) Drop cable strain-relief kit

•

(1) Express cable strain-relief kit

•

(2) Grounding assemblies

•

(2 ft) Spiral wrap

2.2

SCF-6T Closure Contents

•

(1) Tray stacker (Two in -02 configurations)

•

(1) Cover

•

(2) End caps

•

(4) M8x14 Hex bolts

•

(2) Sealing rings

•

(1) Frame assembly

•

(1) Slack basket (none in -02 configurations)

•

(1) Accessory kit (p/n SCF-6T30-ACCY provided with SCF-6T30 and
p/n SCF-6T40-ACCY provided with SCF-6T40)

•

(2) Drop cable strain-relief kit

•

(2) Express cable strain-relief kit

•

(2) Clamping bars

•

(2) Bond clamps

Table 1 — End Cap Gauge Tool

A — Wrench for closing screw
B — Wrench for grounding screw

C — Maximum diameter for tape-wrapped cable in express ports
D — Maximum cable diameter for medium (14 mm) rubber sealing grommet

E — Maximum cable diameter for small (10 mm) rubber sealing grommet

F — Maximum cable diameter for large (18 mm) rubber sealing grommet
G — Wrench for compression screw

H — End cap closing gauge
K — Minimum cable diameter for small (5 mm) rubber sealing grommet

KPA-0500

Содержание SCF-6

































Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды

CORNING SCF-6, Руководство пользователя

Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды