CORNING SCF-6 Скачать руководство пользователя страница 10

Страница: 10 / 32

SCF-6 Canister and Inline Splice Closures

Page 10

SRP 003-485 • Issue 6 • October 2006

Figure 3 — Sheath Removal Lengths

For endspan or drop cable applications

, remove indicated length of cable sheath

and armor (where applicable) as shown in Figure 3 according to cable
manufacturer’s instructions.

Aramid Yarn and
Central Member
15 cm (6 in.)

Buffer tubes

Bare fibers

133 cm (52 in.)

254 cm (100 in.)

Aramid Yarn and
Central Member
15 cm (6 in.)

Buffer tubes

Bare fibers

102 cm (41 in.)

226 cm (89 in.)

Aramid Yarn and
Central Member
15 cm (6 in.)

Bare fibers

Buffer tubes

56 cm (22 in.)

75 cm (30 in.)

198 cm (78 in.)

251 cm (99 in.)

SCF-6T40

SCF-6T30

First End Cap (Attached to Frame Assembly)

Opposite End Cap (Attached to U-Bar)

First End Cap (Attached to Frame Assembly)

Opposite End Cap (Attached to U-Bar)

Aramid Yarn and
Central Member
15 cm (6 in.)

Buffer tubes

Bare fibers

56 cm (22 in.)

198 cm (78 in.)

SCF-6C22 (endspan)

Aramid Yarn and
Central Member
15 cm (6 in.)

Buffer tubes

Bare fibers

75 cm (30 in.)

251 cm (99 in.)

SCF-6C28 (endspan)

KPA-0501

Step 2

Cut the central member of each cable to 15 cm (approximately 6 inches) from the
sheath using side cutters.

Step 3

If aramid yarn is present, leave 15 cm (approximately 6 inches) of yarn for
additional strain-relieving.

Содержание SCF-6

































Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды

CORNING SCF-6, Руководство пользователя

Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды