manualshive.com logo in svg

CORNING SCF-6, Руководство пользователя

Поделиться
Скачать
CORNING SCF-6 Скачать руководство пользователя страница 22

SCF-6 Canister and Inline Splice Closures

Page 22

SRP 003-485 • Issue 6 • October 2006

5.9

Complete Frame Assembly

Reattach the frame assembly to the end cap.

5.10

Attach Strain-relief Bracket

Attach the strain-relief bracket to the frame:

Step 1

Pull the cable back to the end
cap.

Step 2

Center the cable over the port
and slide the attached screw on
the strain-relief bracket into the
slot on the metal frame.

Step 3

Tighten the strain-relief bracket
mounting screw (Figure 28).

Step 4

Repeat Section 5.6 through
Section 5.8 for all drop cables.

Refer to SRP 206-286 (Mechanical End Cap Canister Closure Sealing Checklist) to ensure all

critical

 steps in Section 5.11 for sealing the closure have been performed accurately.

Figure 28 — Install onto Frame

Vinyl Tape

5.11

Tighten End Cap Compression Screw

Secure compression screw into end cap.
Tighten with the end cap gauge until the
clicking sound stops or the screw is butted
against the end cap (Figure 29).

IMPORTANT:

DO NOT overtighten the
screw.

Figure 29 — Tighten Compression Screw

5.12

Splice

5.12.1

Prepare fiber for splicing

Step 1

Place an empty splice tray
into the stacker assembly
with the tray butted
against the fiber
management assembly
(Figure 30).

Figure 30 — Empty Splice Tray

KPA-0474

KPA-0510

H

D

E

G

KPA-0473

Содержание SCF-6

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды