CORNING SCF-6 Скачать руководство пользователя страница 20

Страница: 20 / 32

SCF-6 Canister and Inline Splice Closures

Page 20

SRP 003-485 • Issue 6 • October 2006

Refer to SRP 206-286 (Mechanical End Cap Canister Closure Sealing Checklist) to ensure all

critical

steps in Sections 5.4 and 5.7 for sealing the closure have been performed accurately.

Figure 23 — Sealing Grommet Size

Table 2 — Cable Diameter

Figure 24 — Washer Orientation

Step 3

Place the end cap gauge to determine which size sealing grommet is required
(Figure 23 and Table 2).

Step 4

Place a toothed washer onto the
sealing grommet and insert
both into the opened port from
the strain-relief side of the end
cap (Figure 24). Verify correct
placement of toothed washer on
grommet.

Figure 25 — Lock Nut

Figure 26 — Compression Screw

Sealing Grommet

Toothed Washer

KPA-0468

5.7

Install Drop Port Cable into End Cap

Step 1

Secure the sealing grommet and
toothed washer with the lock
nut on the inside of the end cap.

Step 2

Use the end cap gauge to
tighten the nut until it stops and
is tight (Figure 25).

Step 3

Slide the compression screw
over the cable.

Step 4

Slide the cable through the port
(Figure 26).

KPA-0469

KPA-0470

Cable

KPA-0508

Greater than

or equal to:

Less than:

18 mm

AND

Large

AND

Medium

AND

Small

5 mm

NOTE: Dimensions are for reference only.
Use SCF6 combination wrench to determine cable size.

Cable

Diameter

Range:

If Cable Diameter Is:

Cable is too small for sealing system.

Select

Grommet

Size

Wrench Gauge

"D"

Wrench Gauge

"E"

Wrench Gauge

"K"

Less than "K"

Wrench Gauge

"F"

Wrench Gauge

"D"

Wrench Gauge

"E"

Flat

Requires p/n SCF-KT-G84-F Grommet kit
(purchased separately)

KPA-0509

Содержание SCF-6

































Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды

CORNING SCF-6, Руководство пользователя

Результаты поиска

Содержание SCF-6

Отзывы:

Бренды по названию

Популярные бренды