background image

IMI CORNELIUS INC

ONE CORNELIUS PLACE

ANOKA, MINNESOTA 55303–6234

P/N 163238001
Effective March 1, 1996
Starting with Production 
Serial Number Code 96 A

14

630460070

CORNELIUS LIMITED COMMERCIAL WARRANTY PLAN 

TO THE ORIGINAL OWNER OF A CORNELIUS COMMERCIAL CUBE ICEMAKER

This warranty applies to Icemakers installed within the United States, Canada, Mexico and

Puerto Rico only.

For warranty information outside the U.S., Canada, Mexico and Puerto Rico, contact your nearest IMI Cornelius

Sales Office.

PARTS WARRANTY PERIOD

IMI CORNELIUS INC., hereinafter referred to as CORNELIUS, warrants to the original owner of a new
CORNELIUS commercial cube ice machine (“Machine”) who buys solely for commercial uses, that the Machine
shall be free from defects in material and/or factory workmanship if properly installed, operated and maintained,
under normal and proper use and service conditions with competent supervision. The parts warranty period is
three years (36 months) from the date of installation or 39 months from the date of shipment by CORNELIUS
whichever time period elapses first. With respect to compressor, solid state control board and the evaporator(s),
the warranty period will be five years (60 months) from the date of installation or 63 months from the date of
shipment by CORNELIUS whichever time period elapses first. Warranty on evaporator plating limited, subject to
the incoming water conditions and proper cleaning and maintenance. The obligation of CORNELIUS under this
warranty is limited to repair or replacement (at the option of CORNELIUS) FOB factory in Mason City, Iowa of
the part (or Parts) of any Machine that is proven defective.

LIMITED LIFETIME WARRANTY

In addition to the above stated parts warranty, Cornelius further warrants the stainless steel cabinet
and frame assembly to the original owner at the original installation site against cracks, rust, or
corrosion under normal operating conditions. Models IACS50, AC322 and WC322 are excluded from
this warranty clause.

LIMITED LABOR WARRANTY PERIOD

In addition to the parts warranty, CORNELIUS will pay scheduled straight time labor to repair or replace a
defective component when failure occurs within three years (36 months) from the date of installation or 39
months from the date of shipment by CORNELIUS whichever time period elapses first.  Such service is to be
performed by a service agency authorized by CORNELIUS. Time and rate schedules for labor compensation
will be published periodically by CORNELIUS. Additional expenses including but not limited to travel time,
truck charges, overtime charges, material cost, accessing or removal of the ice machine, normal
prescribed maintenance cleaning, adjustments, and ice purchases are the responsibility of the original
owner.

No parts warranty or labor allowance on the motor compressor assembly will apply when the ice machine’s
refrigeration system is modified with a condenser heat reclaim device, or parts and assemblies not provided by
CORNELIUS, unless CORNELIUS provides approval, in writing, for these modifications for specific locations.

The parts warranty shall not apply when destruction or damage is caused by alterations, unauthorized service,
using other than factory authorized replacement parts, risks of transportation, accidents, misuse, damage by
fire, flood or acts of God. No components or assembly from which the serial number or identification number
has been altered or removed will be covered. Any defective parts to be repaired or replaced must be returned to
us through a CORNELIUS distributor/dealer, transportation charges prepaid, and they must be properly sealed
and tagged. The serial and model number of the Machine and the date of original installation of such Machine
must be given. The warranty of repaired or replaced parts will not extend beyond the period of the original
warranty. The decision of the CORNELIUS Service Department regarding the warrantability of parts and
eligibility for the labor allowance will be final.

Содержание IACS224



















Отзывы: