background image

9

630460070

OWNER-OPERATOR

The installation is  not complete until you are sure the owner-operator understands the cuber operation and his
or her responsibility of preventative maintenance.

Does the owner-operator know:

1. Location of electrical disconnect switch and water shut-off valves?

2. How to start and/or shut down the product, clean and sanitize it.?

3. Bin full operation and reset operation of high pressure cutout (water-cooled and remote products only.)?

4. How to clean the condenser and fan blade?

5. Whom to call for product information and/or service?

CLEANING PROCEDURES

Approved ice machine cleaners by brand names:

S

Lime-A-Way

S

Calgon Nickel Safe (green color only)

NOTE: All ice machine cleaners labeled safe for nickel ARE NOT the brand CALGON NICKEL SAFE.

CAUTION: Ice Machine cleaners are acidic-based chemicals. Before beginning any cleaning
of the cuber, the ice in the storage bin or dispenser must be removed.

WARNING:  When using any chemical rubber gloves and eye protection should be worn.

PREP-CLEANING

Use full-strength ice machine cleaner on a coarse-surface cloth material (such as terry cloth) and wipe down the
inside wall of the evaporator area, the evaporator top. If the water distributor tube has heavy scale build-up, re-
move and soak in a full-strength ice machine clean ( or exchange the tube and clean the scaled tube at a later
date).

CLEANING THE WATER SYSTEM AND EVAPORATOR

1. Set the switch to CLEAN and allow the ice on the evaporator to release the melt away.

2. Remove all ice from the storage bin.

3. Add 3 oz. for a single evaporator of “Calgon Nickel-Safe” or “Lime-A-Away” ice machine cleaner directly

into the water pan. Set switch to CLEAN, circulate for a maximum of 15 minutes.

4. Depress and hold the dump switch to allow the cleaner to drain away.

5. Fill the water pan with clean fresh water, circulate for approximately 3 minute. Depress the DUMP switch

and allow the water to drain away. Repeat this procedure 3 times.

Содержание IACS224



















Отзывы: