Corghi CompactLine EM 9250 Скачать руководство пользователя страница 59

Страница: 59 / 71

128

EM 9250

Operator’s manual

• press the

key.

E 27

Excessive braking time. If the problem persists, contact the technical support
centre.

E 28

Encoder counting error. If the error occurs frequently, call in the technical support
centre.

E 30

Wheel spin device failure. Switch off the machine and call in the technical support
centre.

E 32

The wheel balancer has been jolted during the reading phase. Repeat the wheel
spin.

E F0

Error in reading the 0 notch.

20. OTHER MESSAGES

OP.1

- This message indicates the valve of the wheel that must be brought to

the 12 o'clock position during phases 1 and 5 of optimisation (OPt).

OP.2 180

- This message indicates that the position of the valve must be moved

180° with respect to the previous position (12 o'clock).

Out 2

- This message is displayed when the improvement obtained by optimi-

sation is not sufficient.

- Press the

key to exit the program or the

key to continue

the optimisation phase.

Abo rt

- Notice PREMATURE EXIT from the unbalance optimisation program.

- Press the

key to confirm or the

key to remain in the

programme.

--I- -I--

- Notice TYRE MOUNTING INVERSION ON THE RIM in the OP.5 phase

of the programme.
If you do not want to (or cannot) carry out this operation, press the

key. the machine will provide the instructions to complete

the programme without inversion.

HId dEn

- This message indicates that the operator is in the “positioning the weights

behind the spokes Hidden Weight” programme.

no no

- This message is displayed if the wheel is balanced on the outer side.

in -1-

- This message indicates that the machine is set for acquiring the P1 posi-

tion behind the first spoke

Содержание CompactLine EM 9250








































































Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды

Corghi CompactLine EM 9250, Руководство оператора

Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды